Magnetic polarity influence on machining performance of magnetic field-assisted edm

QR Code

Magnetic polarity influence on machining performance of magnetic field-assisted edm

Electrical discharge machining (EDM) is one of the non-traditional machining techniques where it is commonly used in the mould and die making industry. However, the lengthy machining time in EDM process leads to low material removal rate (MRR). While increasing MRR by increasing peak current value,...

Full description

Bibliographic Details
Main Author:	Mohd Efendee, Awang
Format:	Thesis
Language:	English
Published:	2020
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/34344/ http://umpir.ump.edu.my/id/eprint/34344/1/Magnetic%20polarity%20influence%20on%20machining%20performance.wm.pdf

Similar Items

Effect of magnetic polarity on surface roughness during magnetic field assisted EDM of tool steel
by: A. M., Efendee, et al.
Published: (2018)

Investigation of magnetic field effect on MRR, EWR and surface roughness during EDM of AISI420 tool Steel
by: Efendee, A. M., et al.
Published: (2021)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

ELID grinding and EDM for finish machining
by: Saleh, Tanveer, et al.
Published: (2017)

Magnetic field simulation of pinch mode magnetorheological fluid valve
by: Mohd Zul Asri, Mohd Ramli
Published: (2016)

Minimizing wear of EDM electrode in machining a hard material
by: Muhammad Qahri Harir, Mohd Rapi
Published: (2017)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Optimization of surface roughness in end milling of titanium alloy TI-6AL-4V under the influence of magnetic field from permanents magnets
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Investigation of the influence of the properties of the work and tool materials on performance level of Electrical Discharge Machining (EDM) process
by: A.K.M., N. Amin, et al.
Published: (1997)

Perpetual motion magnetic elevation toy
by: Muhamad Sahddam, Mohd Rozani
Published: (2012)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Near net shape machining by Micro-EDM and Micro-WEDM
by: Saleh, Tanveer, et al.
Published: (2019)

Investigation of the machinability of non-conductive zro2 with different tool electrodes in EDM
by: Moudood, M. A., et al.
Published: (2014)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Exploration of EDM assisted CNT in micro machining using statistical approach
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Solution for instability in magnetizing of toroidial coil winding
by: Ahmad Azwan, Abdul Razak
Published: (2016)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Parametric Optimization in EDM of Ti-6Al-4V using Copper Tungsten Electrode and Positive Polarity: a statistical approach
by: Rahman, Md. Mustafizur, et al.
Published: (2011)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of magnetic field on reduction chatter and of surface roughness in end milling of Titanium Alloy - Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Magnetic Field Simulation of a Thermal Conductivity Measurement Instrument for Magnetorheological Fluid
by: M. S. A., Rahim, et al.
Published: (2017)

A case study on the application of activity based costing on the magnetic inductor
by: Mohd Yazid, Abu, et al.
Published: (2021)

A case study on the application of Mahalanobis-Taguchi system for magnetic component
by: Mohd Yazid, Abu, et al.
Published: (2021)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Effect of size and shape of electrodes on the performance of EDM
by: Khan, Ahsan Ali, et al.
Published: (2008)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Investigation of optimum EDM die sinking parameters in micro dimple machining
by: Lee, Jie Ying, et al.
Published: (2022)

Heat assisted machining of hardened steel AISI D2
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Influence of thermal conductivity cf electrodes on EDM process parameters
by: Khan, Ahsan Ali, et al.
Published: (2012)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Analysis of Magnetic Component Manufacturing Cost Through the Application of Time-Driven Activity-Based Costing
by: Nik Nurharyantie, Nik Mohd Kamil, et al.
Published: (2020)

Heat-assisted machining
by: Amin, A. K. M. Nurul, et al.
Published: (2014)