Comparison of Preparation Methods Effect on the Stability of Compressor oil-based Nanolubricant

QR Code

Comparison of Preparation Methods Effect on the Stability of Compressor oil-based Nanolubricant

The stability evaluation for a nanolubricant is important before any application to a system. The production of nanolubricant can be done using the various method. This study aims to compare the effect of nanolubricant stability on the different preparation methods. The TiO2 nanolubricant with compr...

Full description

Bibliographic Details
Main Authors:	Mohd Farid, Ismail, Wan Hamzah, Azmi, Rizalman, Mamat
Format:	Article
Language:	English
Published:	Akademia Baru Publishing (M) Sdn Bhd 2022
Subjects:	TK Electrical engineering. Electronics Nuclear engineering TL Motor vehicles. Aeronautics. Astronautics
Online Access:	http://umpir.ump.edu.my/id/eprint/33660/ http://umpir.ump.edu.my/id/eprint/33660/1/Comparison%20of%20Preparation%20Methods%20Effect.pdf

Similar Items

Rheological Characteristics and Optimization of Novel TiO2-POE Nanolubricant Using Response Surface Method (RSM) for Air Conditioning System Compressor Application
by: Nugroho, Agus, et al.
Published: (2023)

Extensive stability assessment of tio/polyvinyl ether nanolubricant with physical homogenization
by: Mohd Farid, Ismail, et al.
Published: (2023)

Extensive stability assessment of TiO/polyvinyl ether nanolubricant with physical homogenization
by: Mohd Farid, Ismail, et al.
Published: (2023)

Stability assessment of polyvinyl-ether-based TiO2, SiO2 and their hybrid nanolubricants
by: Mohd Farid, Ismail, et al.
Published: (2023)

Effect of the ethanol-fusel oil mixture on combustion stability, efficiency, and engine performance
by: Mohd Fairusham, Ghazali, et al.
Published: (2025)

Performance of hybrid electric vehicle air-conditioning using SiO2/POE nanolubricant
by: N. N. M., Zawawi, et al.
Published: (2023)

A Tribological Analysis of PAO-Based Hybrid SiO2-TiO2 Nanolubricants
by: R.N.R, Ismail, et al.
Published: (2024)

Performance enhancement and optimization of residential air conditioning system in response to the novel FAl2O3-POE nanolubricant adoption
by: Nugroho, A., et al.
Published: (2023)

Dynamic stability of unguided projectile with 6- DOF trajectory modeling
by: Bashir, Musavir, et al.
Published: (2017)

Control system design for an autonomous helicopter model in hovering using pole placement method
by: Ab. Wahab, Abas, et al.
Published: (2006)

Experimental and numerical study on the aerodynamics and stability characteristics of a canard aircraft
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2019)

Prediction and Optimization of Thermophysical Properties of Hybrid Cellulose Nanocrystal-Copper (II) Oxide Nanolubricant for Tribology Application
by: Sakinah, Hisham, et al.
Published: (2023)

Aerodynamics and Static Stability Characteristics of a Hybrid Buoyant Aerial Vehicle at Low Speed
by: UlHaque, Anwar, et al.
Published: (2015)

Mass Fraction Burn Comparison of Compressed Natural Gas and Gasoline
by: D., Ramasamy, et al.
Published: (2014)

Solid Propellant Motor Design: Comparison of Theoretical and Experimental Data
by: Gunsalam, Henry, et al.
Published: (2006)

Stability analysis of quintuple stellar and planetary systems using a symmetric five-body model
by: M., Shoaib, et al.
Published: (2008)

Development of an energy-efficient hybrid electric vehicle air-conditioning system test rig coupled with nanolubricant
by: Muriban, Jackly, et al.
Published: (2025)

Comparison of design experiment in carbon dioxide (co2) corrosion prediction
by: Feng, Cheng
Published: (2013)

Comparison of automatic and CVT transmission for a car under 1 liter engine
by: Ahmad Mustakim, Mohd Rusli
Published: (2010)

Comparison manual and CVT transmission for a car under 1 liter engine
by: Mohammad Azlan, Abdul Aziz
Published: (2010)

Deceleration performance comparison for passenger car under on-road and off-road driving condition
by: Mohd Khairil, Asri Kamaluddin
Published: (2010)

Estimation of stability derivatives of a delta wing in hypersonic flow
by: Crasta, Asha, et al.
Published: (2012)

Improved vortex lattice method
by: Sulaeman, Erwin
Published: (2011)

Improved doublet point method
by: Sulaeman, Erwin
Published: (2011)

Improved doublet lattice method
by: Sulaeman, Erwin
Published: (2011)

Vibration investigation of passenger car rear suspension system under various road condition and driving maneuever
by: Mohd Farid, Zainudin
Published: (2010)

Heat transfer performance of Ti02- Si02 nanofluid in water-ethylene glycol mixture
by: M. F., Nabil, et al.
Published: (2017)

Application of the aerodynamic discrete element methods
by: Sulaeman, Erwin
Published: (2011)

Painting process improvement for automotive industry
by: Muhammad Farid, M Fathil
Published: (2008)

Injection characteristics study of high-pressure direct injector for Compressed Natural Gas (CNG) using experimental and analytical method
by: Mohd Fadzil, Abdul Rahim, et al.
Published: (2017)

Improvement of rear bumper design
by: Mohd Hafizan, Mamat
Published: (2008)

Flowfield-dependent variant method for moving-boundary problems
by: Zulkafli, Mohd Fadhli, et al.
Published: (2014)

Vibration suppression of rotating disc using eddy current method
by: Mohd Izuan, Hashim
Published: (2013)

Analysis of an automobile suspension arm using the robust design method
by: Hemin M., Mohyaldeen
Published: (2011)

Improvement in stability and thermophysical properties of CNC-MXene nanolubricant for Tribology application
by: Mohd Kamal, Kamarulzaman, et al.
Published: (2023)

Robust design of lower arm suspension using stochastic optimization method
by: Mohd Khairil Azirul, Khairolazar
Published: (2009)

Modeling the magneto- rheological damper using recurrent neural network method
by: Muhammad Afiq Naquiddin, Abd Rahman
Published: (2012)

Evaluation of engine performance and emissions using blends of gasoline, ethanol, and fusel oil
by: S. M., Rosdi, et al.
Published: (2025)

Cost reduction study of automotive part using DFA method : rear lamp
by: Mohd Hafizi, Nawi
Published: (2010)

Cost reduction study of automotive part using dfa method : car seat
by: Muhammad, Mohd Noor
Published: (2012)