Investigating the effect of micro-riblets on the flow and micro-mixing behavior in micro-channel

QR Code

Investigating the effect of micro-riblets on the flow and micro-mixing behavior in micro-channel

Chaotic advection method is usually implemented to design any micro-mixing device, specifically micro-mixers, where the base or the top wide surface is structured for maximum mixing performance. This method comes with several drawbacks, such as the high-pressure drop caused by the structured inner s...

Full description

Bibliographic Details
Main Authors:	Fiona Ling, Wang Ming, Khleif, Ali A., Abdulbari, Hayder A.
Format:	Article
Published:	Taylor & Francis 2020
Subjects:	TP Chemical technology
Online Access:	http://umpir.ump.edu.my/id/eprint/29205/

Similar Items

Insoluble Additives for Enhancing a Blood-Like Liquid Flow in Micro-Channels
by: Abdulbari, Hayder A., et al.
Published: (2017)

Flow behaviour enhancement in micro-channels
by: Lam, Mian Mian
Published: (2017)

Effect of microstructures in microchannel for single phase flow mixing intensification
by: Ling, Fiona W. M., et al.
Published: (2020)

Wall-Pressure Fluctuations of Modified Turbulent Boundary Layer with Riblets
by: Abdulbari, Hayder A., et al.
Published: (2016)

Elucidation of Longitudinally Grooved-Riblets Drag Reduction Performance using Pressure Drop Measurements
by: Abdulbari, Hayder A., et al.
Published: (2017)

Investigating the flow behavior of dilute aloe vera biopolymer solutions in microchannel
by: Fiona Ling, Wang Ming, et al.
Published: (2020)

Enhancing the Flow in Microchannel using Natural Polymeric Additives
by: Fiona Ling, Wang Ming, et al.
Published: (2017)

Liquid Flow Enhancement using Natural Polymeric Additives: Effect of Concentration
by: Abdulbari, Hayder A., et al.
Published: (2016)

Hibiscus Mucilage for Enhancing the Flow in Blood-Stream-Like Microchannel System
by: Abdulbari, Hayder A., et al.
Published: (2017)

Experimental investigations on biopolymer in enhancing the liquid flow in microchannel
by: Abdulbari, Hayder A., et al.
Published: (2018)

Polymer-surfactant complexes effect on the flow in microchannels: An experimental approach
by: Fiona Ling, Wang Ming, et al.
Published: (2020)

Experimental and numerical investigation of fluid flow and heat transfer in circular micro-channel
by: Almaneea, Abdulmajeed
Published: (2020)

Micro-edm for micro-channel fabrication on nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2014)

Fabrication of microfluidic channel using micro end milling and micro electrical discharge milling
by: Ali, Mohammad Yeakub
Published: (2009)

Investigating the effect of nonionic surfactant on the silica nanoparticles formation and morphology in a microfluidic reactor
by: Fiona Ling, Wang Ming, et al.
Published: (2021)

Investigation of the enhancement effect of heat transfer using micro channel
by: Xia, Liang, et al.
Published: (2015)

Polymeric micro-fluidic channel by hot embossing
by: Mohammad, Amar Sami, et al.
Published: (2006)

Drag Reduction Properties of Nanofluids in Microchannels
by: Abdulbari, Hayder A., et al.
Published: (2015)

Drag Reduction by Natural Polymeric Additives in PMDS Microchannel: Effect of Types of Additives
by: Fiona Ling, Wang Ming, et al.
Published: (2017)

Insoluble Nano-powders Additives Enhancing the Flow of Liquid in Microchannel: Effect of Particle Size
by: Fiona Ling, Wang Ming, et al.
Published: (2016)

Combustion characteristic inside micro channel combustor
by: Mohd Rosdzimin Abdul Rahman,, et al.
Published: (2021)

Modelling of subcooled flow boiling in a rectangular micro-channel heat sink
by: Chong, Jen Haw
Published: (2018)

Control of base flows with micro jets
by: Ahmed Ali Baig, Maughal, et al.
Published: (2011)

PDMS-based dual-channel pneumatic micro-actuator
by: Rehman, Tariq, et al.
Published: (2019)

Mass Transfer and Performance of Membrane-Less Micro Fuel Cell: A Review
by: M. N., Nasharudin, et al.
Published: (2014)

Micro structure and Fractography of Multiwalled Carbon Nanotube Reinforced Unsaturated Polyester Nanocomposites
by: Alam, A. K. M. Moshiul, et al.
Published: (2016)

Organic polymers as additives in enhancement of laminar liquid flow in microchannels
by: W.M. Ling, Fiona, et al.
Published: (2018)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Organic Additives for the Enhancement of Laminar Flow in a Brain‐Vessels‐Like Microchannel Assembly
by: Ling, Fiona W. M., et al.
Published: (2019)

Active drag reduction technique for enhancing the liquid-liquid mixing intensity in micromixers
by: Abdulbari, Hayder A.
Published: (2016)

Micro connector fabricated by micro process technology
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2000)

Micro- and nano-scale fluid flow and heat transfer with phase change in a channel
by: Sun, Qiangqiang
Published: (2021)

Analysis and prediction of micro injection molding part using moldflow simulation software
by: Mohammad Farhan, Othman
Published: (2012)

Effects of nano-and micro-sized inorganic filers on the performance of epoxy hybrid nanocoatings
by: Parimalam, Muvinkumar, et al.
Published: (2019)

A Review on Micro-manufacturing, Micro-forming and Their Key Issues
by: A. R., Razali, et al.
Published: (2013)

Effect of residence time on the morphology of silica nanoparticles synthesized in a microfluidic reactor
by: Fiona Ling, Wang Ming, et al.
Published: (2021)

Preliminary Study on The Effect of Inlet Pressure of Standard Slit Interdigital Micro Mixer Towards Mixing by Computational Fluid Dynamics
by: Termizi, Siti Nor Azreen Ahmad, et al.
Published: (2013)

Computational investigation of boiling flows within micro-pin fin evaporators for thermal management of high-power density micro-electronics
by: El Mellas, Ismail
Published: (2024)

Formulation of a new flow improver using halba seeds
by: Abdulbari, Hayder A.
Published: (2011)

Numerical Analysis of Flow and Heat Transfer Characteristics of CO2 at Vapour and Supercritical Phases in Micro-Channels
by: N. T., Rao, et al.
Published: (2016)