Hot cold tumbler

QR Code

Hot cold tumbler

The project Hot Cold Tumbler aims to heat and cool drinking water without using wired electrical supply. With a single selection on the button, users are able to make the favorite hot or cold drinks and it is portable. Hence, it's applicable to use even on high terrain or during camping. The ge...

Full description

Bibliographic Details
Main Author:	Robin, Lee Chiap Loong
Format:	Undergraduates Project Papers
Language:	English
Published:	2016
Subjects:	T Technology (General) TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/26041/ http://umpir.ump.edu.my/id/eprint/26041/1/Hot%20cold.pdf

Similar Items

Hot cold tumbler
by: Chong, Chee Keong
Published: (2017)

Development and Testing of Hot Cold Tumbler Operating on Peltier Effect
by: Robin, Lee, et al.
Published: (2017)

Experimental and Numerical Simulation of Hot Embossing for Fabrication of Glass Microlens Array
by: Lee, Helen May Shian, et al.
Published: (2022)

Performance of IBS lightweight cold-formed steel roof truss
by: Al-Shaquerin, Katman
Published: (2012)

Rapid Fabrication of Glass Micro and Nanostructures via Laser-assisted Hot Embossing
by: Lee, Helen May Shian, et al.
Published: (2023)

Hot Embossing of Micro Grating and Its Replication Accuracy
by: Muhammad Syahrir, Ahmad, et al.
Published: (2024)

Experimental Validation for Hot Stamping Process by Using Taguchi Method
by: Mohd Fawzi, Zamri, et al.
Published: (2016)

Numerical Model of Heat Transfer Coefficient in Hot Stamping Process
by: Mohd Ali Hanafiah, Shaharudin, et al.
Published: (2017)

Design of cooling channel in hot stamping tool by heuristic approach
by: Mohd Fawzi, Zamri
Published: (2017)

Prevention of Crack In Stretch Flanging Process Using Hot Stamping Technique
by: Y., Mohd Syafiq, et al.
Published: (2017)

Pick and place programmable logic controller system for hot press forming
by: Tan, Yee Siang
Published: (2017)

Time and cost study on cold-formed steel and reinforced concrete construction - a comparison
by: Hu, Wei Kiet
Published: (2008)

Experimental Analysis on Cooling Channels Parameters in Hot Stamping Tools (SKD61)
by: M. Farid, M. Sharif, et al.
Published: (2014)

Condition monitoring of deep drilling process for cooling channel making in hot press die
by: Muhamad Aslam, Abdul Raub
Published: (2016)

Tracking Performances of A Hot Air Blower System Using Different Types Of Controllers
by: Ismail, Mohd Khairuddin, et al.
Published: (2014)

Estimation of Thermal Contact Conductance Between Blank and Tool Surface in Hot Stamping Process
by: Zahari, Taha, et al.
Published: (2015)

Study on the effectiveness of Extreme Cold Mist MQL system on turning process of stainless steel AISI 316
by: Ahmad Shahir, Jamaludin, et al.
Published: (2018)

Numerical simulation of hot press forming process for quenchable sheet metal between nanocoolant and chilled water
by: S. K., Lim, et al.
Published: (2018)

Rapid Direct Continuous Method for Hot Embossing of Glass Microlens Array Combined with CO2 Laser Irradiation and External Preheating/Cooling
by: Syarifah Nur Hasanah, Syed Kamarudin, et al.
Published: (2021)

Development of Sustainable Cold Spray Coatings and 3D Additive Manufacturing Components for Repair/Manufacturing Applications: A Critical Review
by: Pathak, Sunil, et al.
Published: (2017)

Estimation of thermal contact conductance value between boron steel blank and tool surface at different value of applied pressure in hot stamping process
by: Mohd Ali Hanafiah, Shaharudin
Published: (2014)

Cyclic extrusion compression back pressure technique for hot forging process in direct recycling of aluminium 6061 machining chip
by: Shahrom, Mohd Syahmi, et al.
Published: (2017)

Heuristic design of U-shaped die cooling channel for producing ultra-high strength steel using hot press forming
by: Mohd Fawzi, Zamri, et al.
Published: (2018)

Heuristic Optimization of Cooling Channel Design in the Hot Stamping Die for Hot Stamping Process
by: Mohd Fawzi, Zamri, et al.
Published: (2015)

Go - Life Enterprise: "Fruit Cutter Tumbler" / Muhammad Shakir Zakaria...[et.al]
by: Zakaria, Muhammad Shakir, et al.
Published: (2017)

Optimizing the synthesis of alumina inserts using hot isostatic pressing (HIP)
by: Ariff, Tasnim Firdaus, et al.
Published: (2017)

Hot embossing and injection molding of three-dimensional microcomponents
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Development of hot stamping tool by using indirect hot stamping for basic bending part (u-shape)
by: Mohd Fawzi, Zamri, et al.
Published: (2014)

Comparison of Cooling Performance Between High Thermal Conductivity Steel (HTCS 150) and Hot Work Tool Steel (SKD 61) Insert for Experimental Tool Using Finite Element Analysis
by: Mohd Fawzi, Zamri, et al.
Published: (2014)

Polymeric micro-fluidic channel by hot embossing
by: Mohammad, Amar Sami, et al.
Published: (2006)

论沙巴州根地咬木板业的挑战与转型——以第三阶段之李健圣为口述访谈对象
by: Thien, Vui Loong, et al.
Published: (2016)

Machining cost in conventional and hot machining: comparison and modelling
by: Elhadie, Mohamed, et al.
Published: (2011)

Developing a prototype micro hot embossing setup
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Conjectured the behaviour of a recycled metal matrix composite (mmc–alr) developed through hot press forging by means of 3d fem simulation
by: Ahmad, Azlan, et al.
Published: (2018)

Migrating supply chain management process online: A study in Malaysian companies
by: Loong, Alain Chong Yee, et al.
Published: (2006)

Evaluation of glass nano/microstructures replication fidelity after laser-assisted hot embossing process
by: Lee, May Shian Helen
Published: (2023)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Micromilling performance analysis – cold air assisted aluminium machining behaviour observation
by: Nurul Hasya, .Md Kamil, et al.
Published: (2022)

Characterization of nanocoolant for improving cooling channel design in hot press forming
by: Yusoff, A. R., et al.
Published: (2018)

Experimental of Hot Machining for Stainless Steel 316L Cutting Process
by: Cholis, N., et al.
Published: (2024)