Optimization of process parameters of injection moldings for plastic pallets manufacturing industry

QR Code

Optimization of process parameters of injection moldings for plastic pallets manufacturing industry

Plastics have been heavily used in industries like automobile, manufacturing, electrical and electronics industry all over the world. Injection molding is one of the ways to process plastics polymers. However, one of the difficulties they have to face is to set the optimal parameter for the injectio...

Full description

Bibliographic Details
Main Authors:	Vivekanandan, Panneerselvam, Faiz, Mohd Turan
Format:	Article
Language:	English
Published:	Penerbit UMP 2019
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/24769/ http://umpir.ump.edu.my/id/eprint/24769/7/Optimization%20of%20Process%20Parameters%20of%20Injection%20Moldings%20for%20Plastic%20Pallets.pdf

Similar Items

Optimisation of injection moulding process parameters using taguchi and desirability function
by: Vivekanandan, Panneerselvam
Published: (2020)

Optimisation of Injection Moulding Process Parameter Using Taguchi and Desirability Function
by: Vivekanandan, Panneerselvam, et al.
Published: (2021)

Multi Response Optimisation of Injection Moulding Process Parameter Using Taguchi and Desirability Function
by: Vivekanandan, Panneerselvam, et al.
Published: (2020)

Microcontroller based boost converter for vibration power harvester
by: Vivekanandan, Panneerselvam
Published: (2017)

Orthogonal array technique for optimizing the sintering parameter of the metal injection molding (MIM) compact: best flexure strength
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)

The influence of injection molding parameter on properties of thermally conductive plastic
by: Azis, N. Hafizah, et al.
Published: (2017)

Incorporating attitudinal parameter in assessing sustainability of Malaysia manufacturing industry
by: Wan Nurul Syahirah, Wan Lanang, et al.
Published: (2018)

Investigation of ductile iron in mold treatment process parameter
by: Yap, Min Choo
Published: (2009)

Injection molding parameter optimization of titanium alloy powder mix with palm stearin and polyethylene for green defects using taguchi method
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Optimization parameters to reduce the warpage defect of plastic injection molding process for a thin-shell part using design of experiment
by: Radhwan, H., et al.
Published: (2019)

Optimisation of Injection Moulding Process Parameters
by: Guna Rao, Kishyen Raao, et al.
Published: (2024)

Rheological investigation of water atomized metal injection molding (MIM) feedstock for processibility prediction
by: Jamaludin, Khairur Rijal, et al.
Published: (2010)

The mold cost estimation calculator for plastic injection mold manufacturing
by: Kamalrudin, massila, et al.
Published: (2008)

Injection molding parameter optimization using the Taguchi method for highest green strength for bimodal powder mixture with SS316L in PEG and PMMA
by: Jamaludina, K. R., et al.
Published: (2008)

Simulation on effect of preform diameter in injection stretch blow molding
by: Tan, Z Q, et al.
Published: (2018)

Lean manufacturing implementation in a plastic molding industry
by: Mohd Yusuff, Rosnah, et al.
Published: (2012)

Fabrication of microcomponents by injection molding
by: Yuan , S., et al.
Published: (2004)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Application of Integrated Fuzzy-AHP for Design Concept Evaluation: A Case Study on Mold Design Selection
by: Faiz, Mohd Turan, et al.
Published: (2015)

Flow behaviour to determine the defects of green part in metal injection molding
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Effects of process parameters on selected properties of liquid compression-molded vinyl ester sheets
by: Abd. Rahman, Mohamed, et al.
Published: (2011)

Modeling and Optimization of Injection Molding Process Parameters for a Plastic Cell Phone Housing Component
by: Rajalingam, Sokkalingam, et al.
Published: (2013)

Warpage analysis on thick shell part using response surface methodology (RSM) and bat algorithm (BA) to optimize parameter setting in injection molding process
by: Ch'Ng, S. Q., et al.
Published: (2018)

Process optimization in rubber injection moulding manufacturing / Ng Yeow Chian
by: Ng, Yeow Chian
Published: (2019)

3D printed mold insert infill analysis for injection molding application
by: Nur Syamimi, Mohd Salleh, et al.
Published: (2024)

Rheological characterization of water atomised stainless steel powder for micro metal injection molding
by: Ibrahim, Mohd. Halim Irwan, et al.
Published: (2009)

Framework of Sustainability Assessment (FSA) method for manufacturing industry in Malaysia
by: Nur Soliha, Sahimi, et al.
Published: (2018)

Design Evaluation Method for Design Engineer in Manufacturing Industries using Integrated Rough-Grey Analysis Approach
by: Faiz, Mohd Turan, et al.
Published: (2014)

Optimization of injection molding parameters for WC-TaC-6Co
by: Prathabrao, M., et al.
Published: (2019)

Redesign of a hand pallet truck by integrating ergonomics analysis and quality function deployment
by: Isa, Halim, et al.
Published: (2009)

Quality characteristics of thin-walled plastic injection parts
by: Noh, Shahril
Published: (2010)

Hot embossing and injection molding of three-dimensional microcomponents
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Observation of polypropylene (PP) melt flow on macro and micro cavities during filling phase of injection molding
by: M., Azuddin, et al.
Published: (2011)

Optimization processability of ss316l used natural hydroxyapatite from waste tilapia fish bones in metal injection molding
by: Mustafa, Najwa
Published: (2019)

Particle size and injection temperature effect on the injection molding of SS316l powder
by: Jamaludin, Khairur Rijal, et al.
Published: (2008)

An influence of a binder system to the rheological behavior of the SS16l metal injection molding (MIM) feedstock
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)

A new material supply mechanism for plunger type injection molding
by: Mohd Syahmi, Mohd Nong
Published: (2013)

Optimization Of Injection Molding Parameters Fo Production Of Polypropylene Plastic Tray Using Taguchi Method
by: Wan, Kok Seong
Published: (2005)

Mold design for plastics injection molding process (two colors) and analysis of gates location
by: Ahmad Zulhelmi, Muhamad
Published: (2009)

Effects of heat transfer in jig molds in injection casting / Hussam Abdulla Moussa Mouhanna
by: Hussam Abdulla Moussa, Mouhanna
Published: (2019)