Torque control analysis of platform based end effector ankle foot orthosis for rehabilitation

QR Code

Torque control analysis of platform based end effector ankle foot orthosis for rehabilitation

This paper presents the control of a one degree of freedom for lower limb platform based end effector ankle foot orthosis for rehabilitation. The plant of the system is obtained through system identification approach and a proportional-integral (PI) architecture is employed to investigate its effica...

Full description

Bibliographic Details
Main Authors:	Abdul Haleem, Habeeb Mohamed, Muhammad Aizzat, Zakaria
Format:	Article
Language:	English
Published:	Penerbit UMP 2019
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/24728/ http://umpir.ump.edu.my/id/eprint/24728/7/Torque%20control%20analysis%20of%20Platform%20Based%20End%20Effector%20Ankle.pdf

Similar Items

Trajectory tracking analysis of planar end-effector upper limb rehabilitation device
by: Lim, H. Y., et al.
Published: (2018)

System Integration and Control of Dynamic Ankle Foot Orthosis for Lower Limb Rehabilitation
by: Anwar, P. P. Abdul Majeed, et al.
Published: (2014)

Design And Testing Of Patient-Specific Ankle Foot Orthosis
by: Md Sukri, Muhammad Ahnaf Ataulah
Published: (2022)

Wearable power assisted pneumatic-based ankle foot orthosis
by: Wong, Zhen Yang
Published: (2012)

Design & analysis of ankle foot orthosis for assisting car driver after ankle surgery
by: Rosdi, Daud, et al.
Published: (2019)

Investigation of characteristics of Kenaf/PLA filament for ankle foot orthosis using fused deposition modelling
by: Shahar, Farah Syazwani
Published: (2021)

Design analysis and structural optimisation of a rigid ankle foot orthosis
by: Mohd Yashim, Wong Paul Tze
Published: (2018)

Design and fabrication of ankle-foot orthoses through 3D scanning and rapid prototyping
by: Engku Ersyad, Engku Abas
Published: (2013)

Fabrication of Stewart platform actuated by pneumatic artificial muscle for foot-ankle rehabilitation
by: Krishnan, Subramaniam
Published: (2019)

A review on the orthotics and prosthetics and the potential of kenaf composites as alternative materials for ankle-foot orthosis
by: Hameed Sultan, Mohamed Thariq, et al.
Published: (2019)

Real-time measurement and gait detection algorithm for motion control of active ankle foot orthosis / Aminuddin Hamid
by: Hamid, Aminuddin
Published: (2015)

Design Of Ankle Foot Orthosis (Afo) Using 3d Printing For Patient Comfort And Agility
by: Ong, Xhin Jie
Published: (2019)

Design And Fabrication Of Ankle Foot Orthosis Utilising 3d Scanner And 3d Printing
by: Ong, Yong Shien
Published: (2021)

Foot Orthosis For Patients With Diabetic Foot Ulcer
by: Kang, Jing Yong
Published: (2018)

Determining foot-ankle mechanism design by mapping the relationships among bones, joints, and ground reaction force
by: Bani Hashim, Ahmad Yusairi, et al.
Published: (2011)

The Control of a Lower Limb Exoskeleton for Gait Rehabilitation: A Hybrid Active Force Control Approach
by: Anwar, P. P. Abdul Majeed, et al.
Published: (2017)

Forward and inverse predictive model for the trajectory tracking control of a lower limb exoskeleton for gait rehabilitation: simulation modelling analysis
by: Muhammad Aizzat, Zakaria, et al.
Published: (2018)

Modelling and Control of an Upper Extremity Exoskeleton for Rehabilitation
by: Zahari, Taha, et al.
Published: (2016)

A randomised controlled trial of laser scanning and casting for the construction of ankle foot orthoses
by: Roberts, Andrew, et al.
Published: (2014)

The control of an upper limb exoskeleton system for passive stroke rehabilitation: An active force control approach
by: Anwar, P. P. Abdul Majeed, et al.
Published: (2018)

Kinematics Analysis of a 3DoF Lower Limb Exoskeleton for Gait Rehabilitation: A Preliminary Investigation
by: Muhammad Aizzat, Zakaria, et al.
Published: (2017)

Design and development of 3D foot scanning rig
by: Muhammad Shahiruddin, Alias
Published: (2013)

Intelligent Machining Systems for Robotic End-Effectors: State-of-the-Art and Toward Future Directions
by: Abdul Nasir, Abd Ghafar, et al.
Published: (2024)

Dynamic Curvature Steering Control for Autonomous Vehicle: Performance Analysis
by: Muhammad Aizzat, Zakaria, et al.
Published: (2016)

Exploring the Design of a Simultaneous, Parallel, Discrete Joint Control Orthosis for Hand Rehabilitation
by: Benson, Daniel Aidan
Published: (2024)

Design And Development Of Robot End-Effector For The Use In Lower-Limb Stroke Rehabilitation Exercises
by: Murugaya, Thivines
Published: (2022)

A Finite Element Analysis of a Human Foot Model to Simulate Neutral Standing on Ground
by: Zahari, Taha, et al.
Published: (2016)

Rain classification for autonomous vehicle navigation using machine learning
by: Abdul Haleem Habeeb, Mohamed, et al.
Published: (2021)

Hardware-in-the-loop study of a hybrid active force control scheme of an upper-limb exoskeleton for passive stroke rehabilitation
by: Anwar, P. P. Abdul Majeed
Published: (2018)

Hardware-in-the-loop study of a hybrid active force control scheme of an upper-limb exoskeleton for passive stroke rehabilitation
by: Anwar, P. P. Abdul Majeed
Published: (2018)

The Assessment of the Clubfoot Children’s Orthotic need for the development of the Foot Abduction Orthosis (FAO) prototype design
by: Sani, Mohd Najib Abdullah, et al.
Published: (2018)

Rain classification for autonomous vehicle navigation : A support vector machine approach
by: Abdul Haleem, Habeeb Mohamed, et al.
Published: (2020)

Investigation of burr formation in micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Foot and Ankle Pain and Injuries in Elite Adult Irish Dancers
by: Cahalan, R., et al.
Published: (2014)

Recent Studies of Human Limbs Rehabilitation Using Mechanomyography Signal: A Survey
by: Muhamad Aliff Imran, Daud, et al.
Published: (2024)

Rover car outdoor localisation for navigation tracking using differential global positioning system estimation
by: Chew, Wi Kang, et al.
Published: (2019)

High speed end milling of single crystal silicon wafer
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Influence of micro end milling process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Open Source Hardware and Software Platform for Robotics and Artificial Intelligence
by: Ng Liang, Shing, et al.
Published: (2015)

Prediction and experimental validation of temperature rise in ductile mode end milling of soda-lime glass
by: Bagum, Mst. Nasima, et al.
Published: (2018)