Suppression of Chatter in High Speed Milling Machine Using Spindle Speed Variation Method with Acoustic Feedback PID Controller

QR Code

Suppression of Chatter in High Speed Milling Machine Using Spindle Speed Variation Method with Acoustic Feedback PID Controller

High speed milling (HSM) process limited by tool failure and dynamic instabilities due to the influence of relative vibration between tool and workpiece, so called chatter. Chatter vibration literally responsible for lower productivity and poor surface quality. In this project, chatter occurrence du...

Full description

Bibliographic Details
Main Authors:	Suparmaniam, Madan Varmma, A. R., Yusoff
Format:	Article
Language:	English
Published:	Penerbit UMP 2019
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/24725/ http://umpir.ump.edu.my/id/eprint/24725/7/Suppression%20of%20Chatter%20in%20High%20Speed%20Milling%20Machine.pdf

Similar Items

Suppression of chatter in high-speed milling machine using spindle speed variation method with microphone feedback PID controlller
by: Madan Varmma, Suparmaniam
Published: (2019)

Spindle speed modulation for chatter suppression in machining process
by: Amirul Hakim, Kamarazaman
Published: (2016)

Suppression of chatter in high speed milling using microcontroller based speed controller by spindle speed variation method
by: Yusoff, A. R., et al.
Published: (2019)

Investigation of Surface Roughness and Tool Wear Length With Varying Combination of Depth of Cut and Feed Rate of Aluminium Alloy and P20 Steel Machining
by: Madan Varmma, Suparmaniam, et al.
Published: (2016)

The method of chatter suppression in end milling operation
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Literature Review of Optimization Techniques for Chatter Suppression In Machining
by: A. R., Yusoff, et al.
Published: (2011)

Relationship of chip load and spindle speed on cutting force and surface integrity for high-speed dry end-milling Hastelloy X material
by: Mohd Nor, Nor Aznan
Published: (2019)

Modelling of PID speed control based collision avoidance system
by: L. M., Keong, et al.
Published: (2020)

Effect of chip load and spindle speed on cutting force of Hastelloy X
by: Mohd Nor, Nor Aznan, et al.
Published: (2020)

Structural analysis of a mini three-axis cnc micro-milling machine with horizontal spindle configuration
by: Saptaji, Kushendarsyah, et al.

Prototype development of optimum irregular milling tools for chatter supression in machining automotive product
by: Yusoff, A. R., et al.

Pso-based PID speed control of traveling wave ultrasonic motor under temperature disturbance
by: Kamal Arifin, Mat Piah, et al.
Published: (2018)

Chatter suppression in end milling of Titanium alloy Ti6Al4V applying permanent magnet clamped adjacent to the workpiece
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Elimination of burr formation during end milling of Polymethyl Methacrylate (PMMA) through high speed machining
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

High speed end milling of single crystal silicon wafer
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Effect of High-Speed Milling Tool Path Strategies on the Surface Roughness of Stavax ESR Mold Insert Machining
by: Mebrahitom, A., et al.
Published: (2016)

Influence of chatter on tool life during end milling of Aluminium and Aluminium alloy on vertical machining centre (VMC)
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Effects of tool path strategies on surface roughness in high speed milling
by: Abdul Rashid, Muhammad
Published: (2012)

Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

PID controller for idle speed control
by: Tuan Kamaruddin, Tengku Nordayana Akma, et al.
Published: (2013)

Influence of chatter of VMC arising during end milling operation and cutting conditions on quality of machined surface
by: A.K.M, N. Amin, et al.
Published: (2001)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Chip serration frequency-the primary cause of chatter during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2009)

Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions
by: Nurul Amin, A. K. M, et al.
Published: (2012)

Sample preparation on ceramics composite for cutting tools in high speed machining
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

Machine learning approach in identifying speed breakers for autonomous driving: an overview
by: Choong, Chun Sern, et al.
Published: (2018)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Optimum design of oil lubricated thrust bearing for hard disk drive with high speed spindle motor
by: Yuta, Sunami, et al.
Published: (2013)

Effect of increasing spindle speed at a constant chip load on cutting force behaviour of Hastelloy X
by: Mohd Nor, N. A., et al.
Published: (2021)

Effect of spindle speed and feed per tooth in feed rate perspective on inconel HX cutting force
by: Mohd Nor, Nor Aznan, et al.
Published: (2021)

The effect of chatter on cutting tool in CNC milling machine
by: Crispin, Julip Jainul
Published: (2009)

Mechanochemical synthesis of hydroxyapatite nanopowder: Effects of rotation speed and milling time on powder properties
by: Syed Abu Bakar, Sharifah Adzila, et al.
Published: (2012)

Labview PID speed controller for DC motor
by: Effizul Syafrin, Abu Bakar
Published: (2008)

Tool Wear Observation During Unconventional Low Speed Machining Using Low Cost Micromilling
by: Ainur Munira, Rosli, et al.
Published: (2021)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Machinability of soda lime glass in high speed end milling
by: Konneh, Mohamed, et al.
Published: (2017)

Role of chip serration frequency in chatter formation during end milling operation of stainless steel
by: Anayet Ullah Patwari, Mohammed, et al.
Published: (2010)

The effect of preheating of work on chatter during end milling of medium carbon steel performed on a Vertical Machining Center (VMC)
by: Amin, A. K. M. Nurul, et al.
Published: (2003)

Multi-response optimizations for high speed ductile mode machining of soda lime glass
by: Bagum, Nasima, et al.
Published: (2015)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)