Performance studies on cryogenic treated carbide cutting tool for turning of AISI304 steel

QR Code

Performance studies on cryogenic treated carbide cutting tool for turning of AISI304 steel

This paper attempts to compare and contrast cryogenic treated and untreated carbide cutting tool in turning operation of AISI304 steel. Machining parameters, namely cutting speed, feed rate and depth of cut are optimized for cryogenic treated tools. Tool life of the insert was determined...

Full description

Bibliographic Details
Main Authors:	Patil, Nagraj, K., Gopalakrishna, B., Sangmesh, Sudhakar, K., Vijayakumar, G. C.
Format:	Article
Language:	English
Published:	Penerbit Universiti Malaysia Pahang 2018
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://umpir.ump.edu.my/id/eprint/23902/ http://umpir.ump.edu.my/id/eprint/23902/1/Performance%20studies%20on%20cryogenic%20treated%20carbide%20cutting.pdf

Similar Items

Relative performances of preheating, cryogenic cooling and hybrid turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Temperature at the tool-chip interface in cryogenic and dry turning of AISI 4340 using carbide tool
by: A. Raof, Natasha, et al.
Published: (2016)

A new approach of applying cryogenic coolant in turning AISI 304 stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Experimental study on hard turning of hardened tool steel with coated carbide cutting tools
by: K. Seveen, K. Muniswaran
Published: (2007)

Magnetic damping in turning of stainless steel aisi 304 for the reduction of machining vibration and tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (2015)

Performance evaluation of coated carbide cutting tools when turning hardened tool steel
by: Tang, Yu Cai
Published: (2006)

Effect of vegetable and mineral oil-in-water emulsion cutting fluids in turning AISI 4340 steel with coated carbide tools / Sunday Albert Lawal
by: Sunday, Albert Lawal
Published: (2013)

Experimental determination of optimum cutting conditions in turning low alloyed steel with cemented carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Implementation of magnetic damping to reduce chatter amplitude and tool wear during turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

The effect of deep cryogenic treatment on the properties of AISI D2 tool steel
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

The effect of deep cryogenic treatment on the properties of AISI D2 tool steel
by: Ahmed Ghazal, Belal, et al.
Published: (2011)

Comparison of dry and cryogenic machining on chip formation and coefficient of friction in turning AISI 4340 alloy steel
by: A. Raof, Natasha, et al.
Published: (2014)

Machining parameters effect in dry turning of AISI 316L stainless steel using coated carbide tools
by: Nur, R., et al.
Published: (2017)

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Noordin, Mohd Yusof, et al.
Published: (2004)

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Noordin, M. Y., et al.
Published: (2004)

Application of response surface methodology in describing the performance of coated carbide tools when turning AISI 1045 steel
by: Nordin, M. Y., et al.
Published: (2004)

Optimization of Tool Wear using Coupled RSM-GA Approach in Turning of Stainless Steel AISI 304 with Magnetic Damping of Tool Shank
by: Amin, A. K. M. Nurul, et al.
Published: (2015)

New tool life models in turning hardened steel AISI 4340 under high cutting speed
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Optimization of tool geometry design for free cutting steel (AISI 12L14) in turning operation
by: Mohammad, Rosdi
Published: (2017)

Experimental study of flank wear in high speed turning of stainless steel AISI 304
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

The effect of cryogenic cooling in machinability of stainless steel during turning
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Study on surface integrity of AISI 1045 carbon steel when machined by carbide cutting tool under wet conditions
by: N. Fauzi, Tamin, et al.
Published: (2017)

Efficient cryogenic cooling during machining of rolled AISI 4340 steel
by: Ahmed, Mirghani Ishak, et al.
Published: (2012)

Optimization of cutting parameters to minimize tooling cost in high speed turning of SS304 using coated carbide tool using genetic algorithm method
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2016)

Feasibility of mild hard turning of stainless steel using coated carbide tool
by: Noordin, M., et al.
Published: (2012)

The Effect of Multiple Pass Cutting on Surface Integrity when Hard Turning of AISI D2 Cold Work Tool Steel
by: Kamely, M. A., et al.
Published: (2007)

Surface roughness IN high speed turning OF alloy steel m303 using carbide tools in dry cutting condition
by: Tahrin Othman,, et al.
Published: (2022)

Effect of Cutting Parameters on Sustainable Machining Performance of Coated Carbide Tool in Dry Turning Process of Stainless Steel 316
by: Bagaber, Salem Abdullah, et al.
Published: (2017)

Hard Turning of Stainless Steel using Wiper Coated Carbide Tool
by: Noordin, M.Y., et al.
Published: (2007)

Finite element simulation of machining AISI 1045 steel using uncoated carbide tool
by: Mohmd Arifin, Nabila Afif
Published: (2012)

Finite element simulation of machining AISI 1045 steel using uncoated carbide tool
by: Mohmd Arifin, Nabila Afif
Published: (2012)

Tool Life of Coated Carbide Cutting Tool when Turning Hardened Stainless Steel under Minimum Quantity Lubricant Using Castor Oil
by: Elmunafi, M., et al.
Published: (2015)

Performance evaluation of coated carbide and coated cermet tools when turning hardened tool steel
by: Mohd. Yusof, Noordin
Published: (2003)

Effect of cutting speed and feed in turning hardened stainless steel using coated carbide cutting tool under minimum quantity lubrication using castor oil
by: Elmunafi, M., et al.
Published: (2015)

Machinability aspects in heat assisted machining of hardened steel AISI H13 using coated carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Optimization of process parameters on EDM milling of stainless steel AISI 304
by: A.K.M, Asif Iqbal, et al.
Published: (2011)

Investigation of Chip and Surface Roughness when Milling AISI304 Stainless Steel
by: K., Kadirgama
Published: (2017)

Dry turning of tempered martensitic stainless tool steel using coated cermet and coated carbide tools.
by: Noordin, M. Y., et al.
Published: (2007)

Machining-induced grain refinement of AISI 4340 alloy steel under dry and cryogenic conditions
by: A. Raof, Natasha, et al.
Published: (2019)

Progressive Tool Flank Wear And Surface Roughness When Turning AISI 1017 Mild Steel Using Reduced Thickness Inserts In Finishing Cutting Conditions
by: S. A., Che Ghani, et al.
Published: (2017)