Regenerative chatter in end milling on mould aluminum via experimental

QR Code

Regenerative chatter in end milling on mould aluminum via experimental

Milling operation is widely used in the manufacturing industry for the metal cutting purpose. For the efficiency of the milling process, high demands on the material removal rate and the surface generation rate are posed. The process parameters, determining these two rates, are restricted by the occ...

Full description

Bibliographic Details
Main Author:	Mohammad Hafizuddin, Mokhtar
Format:	Undergraduates Project Papers
Language:	English
Published:	2007
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://umpir.ump.edu.my/id/eprint/2281/ http://umpir.ump.edu.my/id/eprint/2281/1/MOHAMMAD_HAFIZUDDIN_MOKHTAR.PDF

Similar Items

Regenerative Chatter in End Milling on Mould Aluminum Alloys
by: N. M. Zuki, N. M., et al.
Published: (2008)

The method of chatter suppression in end milling operation
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Chip serration frequency-the primary cause of chatter during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2011)

A novel method for chatter control and improvement of surface finish in end milling
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Application of permanent electromagnet for chatter control in end milling of medium carbon steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Investigations of the causes of chatter in computer aided manufacturing process during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Prediction of chatter in CNC machining based on dynamic cutting force for ball end milling
by: Nor Komariah, Hasfa
Published: (2008)

Prediction of Chatter in CNC Machining based on Dynamic Cutting Force for Ball End Milling
by: R., Daud, et al.
Published: (2009)

A new method for chatter suppression and improvement of surface roughness in end milling of mild steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Influence of the elastic system and cutting parameters on chatter during end milling of aluminium and aluminium alloy on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

High speed milling of mould steel using 1.5mm-diameter end-mills
by: Mohamed , Konneh, et al.
Published: (2011)

Experimental validation for chatter stability prediction
by: Muhammad Azwan, Zainol Abidin
Published: (2012)

Application of permanent electromagnet for chatter control in end milling of Titanium alloy - Ti6Al4V
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
by: M. K. , Nor Khairusshima, et al.
Published: (2011)

The effect of chatter on cutting tool in CNC milling machine
by: Crispin, Julip Jainul
Published: (2009)

A new technique for the investigation of chatter formation during end milling of medium carbon steel (AISI 45)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2
by: Amin, A. K. M. Nurul, et al.
Published: (2008)

Experimental Investigation of Flank Wear in end Milling of Aluminum Alloy with Water-Based TiO2 Nanofluid Lubricant in Minimum Quantity Lubrication Technique
by: Najiha, M. S., et al.
Published: (2016)

Multi-Objective Optimization of Minimum Quantity Lubrication in end Milling of Aluminum Alloy AA6061T6
by: Najiha, M. S., et al.
Published: (2015)

Effect of mould tilt angle on the mechanical properties of as-cast aluminum alloy
by: Hamzah, E., et al.
Published: (2002)

Modeling of the end milling process for aluminum alloy AA6061T6 using hss tool
by: Najiha, M. S., et al.
Published: (2013)

Experimental study on surface integrity in end milling of hastelloy c-2000 superalloy
by: Norhaida, Ab Razak, et al.
Published: (2014)

Integrated chatter avoidance and minimum quantity lubrication conditions for chatter vibration problem in the machining process
by: Wan Azlan, Wan Mohd Nowalid, et al.
Published: (2015)

Vibration issue in micro end milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Experimental and Numerical Study of Cutting Force in End-Milling Operation Using Statistical Method
by: K., Kadirgama, et al.
Published: (2009)

Experimental investigation of vibration chatter in micromilling with minimum quantity lubrication: Analysis of signal-to-noise ratio and variance
by: Mohammad Yeakub, Ali, et al.
Published: (2024)

Prototype development of optimum irregular milling tools for chatter supression in machining automotive product
by: Yusoff, A. R., et al.

Optimization of Surface Roughness in End Milling on Mould Aluminium Alloys (AA6061-T6) Using Response Surface Method and Radian Basis Function Network
by: K., Kadirgama, et al.
Published: (2008)

Evaluation Of Cutting Force in End Milling Process of Aluminum Alloy 6061-T6 Using Tungsten Carbide Inserts with MQL Method Utilizing Hybrid Nanofluid
by: Wahaizad, Safiei, et al.
Published: (2021)

Suppression of chatter in high-speed milling machine using spindle speed variation method with microphone feedback PID controlller
by: Madan Varmma, Suparmaniam
Published: (2019)

Prediction Modeling of Torque in End-milling
by: K., Kadirgama, et al.
Published: (2010)

Experimental investigation of the minimum quantity lubrication in end-milling of AA6061T6 by coated carbide tools
by: Abdul Muhaimin, Aris
Published: (2013)

Experimental investigation of MQL Optimum Parameters In End Milling of AA6061-T6 using Taguchi Method
by: Wahaizad, Safiei, et al.
Published: (2018)

Resonance effect in chatter formation in metal cutting
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Experimental and analytical evaluation of bending for aluminum
by: Nazrith, Zulkafli
Published: (2012)

Experimental Analysis of Aluminum Alloy under Solid Particle Erosion Process
by: Chowdhury, Mohammad Asaduzzaman, et al.
Published: (2016)

Wear mechanism in end milling of Inconel 718
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Prediction Modelling Of Power And Torque In End-Milling
by: K., Kadirgama, et al.
Published: (2009)

Burr Reduction of Micro-milled Microfluidic Channels Mould Using a Tapered Tool
by: Saptaji, Kushendarsyah, et al.
Published: (2017)

Experimental Study on Minimum Quantity Lubrication in End Milling of AA6061-T6 Using Tialn Coated Carbide Tools
by: Najiha, M. S., et al.
Published: (2015)