Effects of drilling parameters in numerical simulation to the bone temperature elevation

QR Code

Effects of drilling parameters in numerical simulation to the bone temperature elevation

Drilling into the bone can produce significant amount of heat which can cause bone necrosis. Understanding the drilling parameters influence to the heat generation is necessary to prevent thermal necrosis to the bone. The aim of this study is to investigate the influence of drilling parameters on bo...

Full description

Bibliographic Details
Main Authors:	Mohd Faizal, Ali Akhbar, Mukhtar, Malik, A. R., Yusoff
Format:	Conference or Workshop Item
Language:	English
Published:	AIP Publishing 2018
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://umpir.ump.edu.my/id/eprint/20171/ http://umpir.ump.edu.my/id/eprint/20171/1/ANEMS2017-final.pdf

Similar Items

Comparison of bone temperature elevation in drilling of human, bovine and porcine bone
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Numerical and experimental investigations on temperature and thermal damage in cortical bone drilling
by: Mohd Faizal, Ali Akhbar
Published: (2020)

Optimization of drilling parameters for thermal bone necrosis prevention
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2018)

Drilling of bone: thermal osteonecrosis regions induced by drilling parameters
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Multi-objective optimization of surgical drill bit to minimize thermal damage in bone-drilling
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Drilling of bone: Effect of drill bit geometries on thermal osteonecrosis risk regions
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Surgical drill bit design and thermomechanical damage in bone drilling: A review
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2021)

Optimization of drill bit geometries for minimum thermal damage in bone drilling
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2024)

Fast & Injurious: Reducing thermal osteonecrosis regions in the drilling of human bone with multi-objective optimization
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2020)

Creep damage analysis and numerical simulation on oil well steel pipe casing at elevated temperatures / Sarmad Khubaib Sarajun Hoda
by: Sarmad Khubaib, Sarajun Hoda
Published: (2021)

Effect Of Twist Drill Geometry And Drilling Parameters On Thrust Force In Single-Shot Drilling Of Stack-Up Material
by: Chim, Yi Shen
Published: (2017)

Optimization of Electro Discharge Machining Parameters for Drilling Titanium in Small Holes Using Taguchi Method
by: Hazami, Che Hussain, et al.
Published: (2014)

Determining Optimum EDM Parameters in Drilling a Small Hole by Taguchi Method
by: A. R., Yusoff, et al.
Published: (2009)

Numerical modeling and simulation of material removal in laser drilling of thin metal sheets using meshfree collocation methods / Diaa Abdelmonem Mahmoud Abidou
by: Diaa Abdelmonem , Mahmoud Abidou
Published: (2017)

Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates
by: Abd Halim, Nor Farah Huda, et al.
Published: (2011)

Effect of drill point angle on surface integrity when drilling titanium alloy
by: Murad, Muhamad Nasir, et al.
Published: (2014)

Evaluation of elevated temperature oxidation of higher manganese ni-resist alloy
by: Khairul Ihsan, Yaakob, et al.
Published: (2024)

Effect of laser micro-drilling parameters on hole geometry and hole formation of thin sheet SS304
by: Haneef, M. S., et al.
Published: (2023)

Numerical simulation of green compacts
by: Hrairi, Meftah, et al.
Published: (2011)

Numerical simulation of liquid atomisation
by: Wan Muhammad Mukhlis, Wan Ab Latif
Published: (2010)

Air-Drill With Accelerometer And Microphone For Composite Drilling Application
by: Wei Tong, Koh
Published: (2022)

Experimental analysis on drilling process of CFRP composite laminates
by: Latifah, Md Yusoff
Published: (2008)

Artificial Neural Network: The Alternative Method to Obtain the Dimension of Ankle Bone Parameters
by: R., Daud, et al.
Published: (2017)

Effect of process parameters on surface roughness in HPC drilling of AISI 1055 steel / H.V. Shete and M.S. Sohani
by: H.V., Shete, et al.
Published: (2020)

Performance of TialN coated carbide tool in peck drilling stainless steel SS316L with pressurized minimum quantity lubrication
by: M., Malik, et al.
Published: (2014)

Towards a numerical simulation of supersonic mixing & combustion
by: Kamel, Mohammed, et al.
Published: (2013)

Effect of cutting parameters on the hole diameter and surface roughness for dry drilling of aluminum alloy 6061
by: Ahamed, Ahmad Fauzi
Published: (2010)

Numerical Investigation On The Effects Of Geometrical Parameters On Film Cooling Performance
by: Ali, Amir Hussein
Published: (2013)

In-Situ Measurement of Electrode Wear During EDM Drilling using Vision System
by: Zamzuri, Hamedon, et al.
Published: (2018)

Numerical simulation of single point diamond turning
by: Teoh, Yeong Chia
Published: (2009)

Numerical Simulation Of A Microchannel For Microelectronic Cooling
by: Wong, Wai Hing, et al.
Published: (2007)

Numerical Simulation of Fibre Orientation in Simple Injection Molding Processes
by: Oumer, A.N., et al.
Published: (2009)

Experimental and numerical simulation of hollow structure under compression loading
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2012)

Numerical Simulation of Multiple Arrays Arrangement of Micro Hydro Power Turbines
by: At-Tasneem, Mohd Amin, et al.
Published: (2014)

Quality And Performance Analysis Of Drill Tools
by: Subramonian, Sivarao
Published: (2005)

Control of automatic drilling machine by PLC
by: Rahman , Md Mozasser, et al.
Published: (2011)

Simulation of gaseous fuel injector geometries of mult holes nozzle by using CNG engine
by: Muhamad Akhbar Osman, Md. Hashim
Published: (2009)

Numerical simulation of nanofluid forced convection heat transfer
by: Mohd Taufidd, Tawang
Published: (2010)

Numerical Simulation of Natural Convection in an Inclined Square Cavity
by: Munir, F.A, et al.
Published: (2011)

Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates
by: Abd Halim, Nor Farah Huda, et al.
Published: (2011)