Mold design & surface analysis of casted material

QR Code

Mold design & surface analysis of casted material

Casting is a manufacturing process where a solid is melted, heated to proper temperature, and is then poured into a cavity or mold, which contains it in the proper shape during solidification. Casting process generally is classified as expendable mold or permanent mold. These researches consist of d...

Full description

Bibliographic Details
Main Author:	Annafi, Mohd Khobori
Format:	Undergraduates Project Papers
Language:	English
Published:	2010
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/1397/ http://umpir.ump.edu.my/id/eprint/1397/1/Mold%20design%20%26%20surface%20analysis%20of%20casted%20material.pdf

Similar Items

Design and Simulation on Investment Casting Mold for Metal Matrix Composite Material
by: Taufik, Roni Sahroni, et al.
Published: (2011)

A study on mold material and coating effect in sand casting process
by: Muhammad Fakhri, Zainuddin
Published: (2009)

Effect of mold designs on molten metal behaviour in high-pressure die casting
by: Ibrahim, M.D, et al.
Published: (2017)

Mould design and mechanical analysis of the casted material
by: Mohd Azuan, Abu Shah
Published: (2010)

Design and fabrication of the blow mold component
by: Mohd Azuan, Abu Shah
Published: (2007)

Design and Simulation on Cast metal Matrix Composite by Investment Casting
by: Taufik, Roni Sahroni, et al.
Published: (2011)

Effects of heat transfer in jig molds in injection casting / Hussam Abdulla Moussa Mouhanna
by: Hussam Abdulla Moussa, Mouhanna
Published: (2019)

Design and fabrication of drain cover by casting process
by: Muhamad Amin, Ab Rasak
Published: (2012)

Design and fabrication of hole cover by casting process
by: Muhammad Kamili, Zahidi
Published: (2011)

Effect of casting temperature on dimensional accuracy in gravity casting
by: Mohd Shariman, Razali
Published: (2009)

Design Simulation of Filing Sequence and Solidification Time for Cast Metal Matrix Composite by Low Pressure Die Casting
by: Taufik, Roni Sahroni, et al.
Published: (2011)

Molding of three-dimensional microcomponents
by: Hung, W. N. P., et al.
Published: (2006)

Application of Integrated Fuzzy-AHP for Design Concept Evaluation: A Case Study on Mold Design Selection
by: Faiz, Mohd Turan, et al.
Published: (2015)

Design and Simulation on Compressor Metal Matrix Composite by Investment Casting
by: Taufik, Roni Sahroni, et al.
Published: (2011)

Improvement of Form Accuracy and Surface Integrity of Si-HDPE Hybrid Micro-Lens Arrays in Press Molding
by: Ahmad Rosli, Abdul Manaf, et al.
Published: (2017)

Effect of High-Speed Milling Tool Path Strategies on the Surface Roughness of Stavax ESR Mold Insert Machining
by: Mebrahitom, A., et al.
Published: (2016)

3D printed mold insert infill analysis for injection molding application
by: Nur Syamimi, Mohd Salleh, et al.
Published: (2024)

A new material supply mechanism for plunger type injection molding
by: Mohd Syahmi, Mohd Nong
Published: (2013)

Design and simulation on investment casting mold for metal matrix composite material
by: Sahroni, Taufik Roni, et al.
Published: (2011)

Investigation of ductile iron in mold treatment process parameter
by: Yap, Min Choo
Published: (2009)

Defect analysis on investment casting: a case study
by: Sabudin, Sulastri
Published: (2004)

Simulation on effect of preform diameter in injection stretch blow molding
by: Tan, Z Q, et al.
Published: (2018)

Optimization of process parameters of injection moldings for plastic pallets manufacturing industry
by: Vivekanandan, Panneerselvam, et al.
Published: (2019)

Peningkatan Mutu Molding Injeksi dengan Metode DMAIC Six Sigma
by: Sihombing, Haeryip, et al.
Published: (2011)

Flow behaviour to determine the defects of green part in metal injection molding
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Rheocasting and Thixocasting: Semi-Solid Casting Technologies
by: S.THIRU,, CHITRAMBALAM
Published: (2010)

The effects of vortex gate design on mechanical strength of thin section casting of LM 25 (Al---7Si-0.3Mg) aluminum casting alloy
by: Subhi, Zaid Ali
Published: (2012)

Fe evaluation of thermal property of mould wall material for investment casting and the effect of layers on the hardness of the casting product
by: Phuan, Yoong Jiann
Published: (2004)

Evaluation of Surface Roughness and Power Consumption in Machining FCD 450 Cast Iron using Coated and Uncoated Irregular Milling Tools
by: A. R., Yusoff, et al.
Published: (2015)

Effect of Lead Addition in LM6 Alloy Castings
by: S.THIRU,, CHITRAMBALAM
Published: (2010)

The effect of stucco system in ceramic shell investment casting
by: Mohamad Badari, Siti Norbahiyah, et al.
Published: (2011)

Effects of process parameters on selected properties of liquid compression-molded vinyl ester sheets
by: Abd. Rahman, Mohamed, et al.
Published: (2011)

Rheological characterization of water atomised stainless steel powder for micro metal injection molding
by: Ibrahim, Mohd. Halim Irwan, et al.
Published: (2009)

Investigation of brass microstructure and mechanical properties using metal casting
by: Nur Hamizah, Minhat
Published: (2010)

Effect of melting temperature on dimensional accuracy in sand casting product
by: Ahmad Faizal, Mohamad
Published: (2009)

Rheological investigation of water atomized metal injection molding (MIM) feedstock for processibility prediction
by: Jamaludin, Khairur Rijal, et al.
Published: (2010)

Collapsibility of PMMA based material in direct investment casting
by: Shukri, Muhammad Shazwan, et al.
Published: (2018)

Development of low density polyethylene/sago based biofilm via blow film molding technique
by: Wan Abdul Rahman, Wan Aizan, et al.
Published: (2009)

Fabrication of microcomponents by injection molding
by: Yuan , S., et al.
Published: (2004)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)