Investigation of ductile iron in mold treatment process parameter

QR Code

Investigation of ductile iron in mold treatment process parameter

Ductile iron was first developed in 1943 and it is widely used in automotive industry.The difference between cast iron and ductile iron is due to the presence of spheroid graphite in the matrix of ductile iron which is not found in brittle cast iron. Ductile iron possesses higher ductility and tensi...

Full description

Bibliographic Details
Main Author:	Yap, Min Choo
Format:	Undergraduates Project Papers
Language:	English
Published:	2009
Subjects:	TS Manufactures
Online Access:	http://umpir.ump.edu.my/id/eprint/1075/ http://umpir.ump.edu.my/id/eprint/1075/1/Yap%2C_Min_Choo.pdf

Similar Items

Investigation of ductile iron 'sandwich' treatment process parameter
by: Md Fakhrurazi, Abdul Halil
Published: (2009)

Investigation of thin wall ductile iron parameter
by: Mohd Khairi, Mohd Noor
Published: (2009)

Effects of austempering treatment on mechanical properties of ductile iron
by: Ahmed Ghazal, Belal, et al.
Published: (2011)

Optimization of process parameters of injection moldings for plastic pallets manufacturing industry
by: Vivekanandan, Panneerselvam, et al.
Published: (2019)

Effects of process parameters on selected properties of liquid compression-molded vinyl ester sheets
by: Abd. Rahman, Mohamed, et al.
Published: (2011)

Rheological investigation of water atomized metal injection molding (MIM) feedstock for processibility prediction
by: Jamaludin, Khairur Rijal, et al.
Published: (2010)

A Study on Conversion of Higher Sulfur Pig Iron to Ductile Iron Using In-Mold Treatment Technique
by: Mohd Rashidi, Maarof, et al.
Published: (2012)

A study on mold material and coating effect in sand casting process
by: Muhammad Fakhri, Zainuddin
Published: (2009)

Molding of three-dimensional microcomponents
by: Hung, W. N. P., et al.
Published: (2006)

Orthogonal array technique for optimizing the sintering parameter of the metal injection molding (MIM) compact: best flexure strength
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)

Design and fabrication of the blow mold component
by: Mohd Azuan, Abu Shah
Published: (2007)

The effect of nodularisation parameters on the quality of ductile iron
by: Maarof, Mohd. Rashidi
Published: (2006)

Injection molding parameter optimization of titanium alloy powder mix with palm stearin and polyethylene for green defects using taguchi method
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Mold design & surface analysis of casted material
by: Annafi, Mohd Khobori
Published: (2010)

Multi-response optimizations for high speed ductile mode machining of soda lime glass
by: Bagum, Nasima, et al.
Published: (2015)

Injection molding parameter optimization using the Taguchi method for highest green strength for bimodal powder mixture with SS316L in PEG and PMMA
by: Jamaludina, K. R., et al.
Published: (2008)

Prediction and experimental validation of temperature rise in ductile mode end milling of soda-lime glass
by: Bagum, Mst. Nasima, et al.
Published: (2018)

Simulation on effect of preform diameter in injection stretch blow molding
by: Tan, Z Q, et al.
Published: (2018)

Application of ductility exhaustion based damage model to predict creep rupture time of grade 92 steel
by: Nasrul Azuan, Alang, et al.
Published: (2019)

Flow behaviour to determine the defects of green part in metal injection molding
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Peningkatan Mutu Molding Injeksi dengan Metode DMAIC Six Sigma
by: Sihombing, Haeryip, et al.
Published: (2011)

Design and Simulation on Investment Casting Mold for Metal Matrix Composite Material
by: Taufik, Roni Sahroni, et al.
Published: (2011)

An investigation on the surface austempering of ductile cast iron
by: Fayyaz, Abdolali, et al.
Published: (2017)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Effect of mold designs on molten metal behaviour in high-pressure die casting
by: Ibrahim, M.D, et al.
Published: (2017)

3D printed mold insert infill analysis for injection molding application
by: Nur Syamimi, Mohd Salleh, et al.
Published: (2024)

Rheological characterization of water atomised stainless steel powder for micro metal injection molding
by: Ibrahim, Mohd. Halim Irwan, et al.
Published: (2009)

Development of low density polyethylene/sago based biofilm via blow film molding technique
by: Wan Abdul Rahman, Wan Aizan, et al.
Published: (2009)

An improvement of mechanical properties of ductile iron and niobium alloyed ductile iron through new heat treatment cycles / Bulan Abdullah
by: Abdullah, Bulan
Published: (2012)

An improvement of mechanical properties of ductile iron and niobium alloyed ductile iron through new heat treatment cycles / Bulan Abdullah
by: Abdullah, Bulan
Published: (2011)

Experimental investigation on magnetorheological finishing process parameters
by: Abdul Wahab, Hashmi, et al.
Published: (2022)

Fabrication of microcomponents by injection molding
by: Yuan , S., et al.
Published: (2004)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Warpage analysis on thick shell part using response surface methodology (RSM) and bat algorithm (BA) to optimize parameter setting in injection molding process
by: Ch'Ng, S. Q., et al.
Published: (2018)

Implementation of single minute exchange die (SMED) technique to accelerate the mold changing time at sme company
by: Muhamad Nasruldin, Hashim
Published: (2012)

Application of Integrated Fuzzy-AHP for Design Concept Evaluation: A Case Study on Mold Design Selection
by: Faiz, Mohd Turan, et al.
Published: (2015)

Improvement of Form Accuracy and Surface Integrity of Si-HDPE Hybrid Micro-Lens Arrays in Press Molding
by: Ahmad Rosli, Abdul Manaf, et al.
Published: (2017)

Observation of polypropylene (PP) melt flow on macro and micro cavities during filling phase of injection molding
by: M., Azuddin, et al.
Published: (2011)

Effect of Machining Process Parameters on Acceleration Signal in Determining Surface Quality of Milling Process at Ductile Iron
by: Norlida, Jamil, et al.
Published: (2019)

An influence of a binder system to the rheological behavior of the SS16l metal injection molding (MIM) feedstock
by: Jamaludin, Khairur Rijal, et al.
Published: (2009)