Design of a plastic injection mold (8 cavities) / Muhammad Fadzli Abdul Rahman and Md Zulkhairi Ismail

QR Code

Design of a plastic injection mold (8 cavities) / Muhammad Fadzli Abdul Rahman and Md Zulkhairi Ismail

This project work reports the design work on up-grading a mold die. A 2 cavities mold was up-graded to 8 cavities. This up-grading will increase the efficiency, time for one cycle, production rate and life time of mold. When the mold is up-graded to 8 cavities it becomes more economical and also wil...

Full description

Bibliographic Details
Main Authors:	Abdul Rahman, Muhammad Fadzli, Ismail, Md Zulkhairi
Format:	Student Project
Language:	English
Published:	Faculty of Mechanical Engineering 2001
Subjects:	Engineering machinery, tools, and implements
Online Access:	https://ir.uitm.edu.my/id/eprint/20718/

Similar Items

State of the art report of waste tyre in civil engineering application / Lenny A. Rahman
by: A. Rahman, Lenny
Published: (2007)

Optimization of milling carbon fiber reinforced plastic using RSM
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Optimization of milling carbon fibre reinforced plastic under chilled air machining
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Study on machinability effect of surface roughness in milling kenaf fiber reinforced plastic composite (unidirectional) using response surface methodology
by: Harun, Azmi, et al.
Published: (2016)

Physical, chemical and mechanical characterization of heat treated Malaysian hardwood timbers / Nur Ilya Farhana Md Noh
by: Md Noh, Nur Ilya Farhana
Published: (2018)

A case study of chilled water air-conditioning system in UiTM Penang / Md Zainizam Ngadiman
by: Ngadiman, Md Zainizam
Published: (2019)

Simulation study of welding joint by using SYSWELD / Mohd Shahar Sulaiman
by: Sulaiman, Mohd Shahar
Published: (2009)

Micro-electro discharge machining of nonconductive zirconia ceramic: investigation of MRR and recast layer hardness
by: Banu, Asfana, et al.
Published: (2014)

The optimization study on the tool wear of carbide cutting tool during milling Carbon Fibre Reinforced (CFRP) using Response Surface Methodology (RSM)
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2018)

Material characterization of a doped triangular silicon nanowire using raman spectroscopy
by: Za'bah, Nor Farahidah, et al.
Published: (2018)

Content comparative investigation on tool wear during end milling of AISI H13 steel with different tool path strategies
by: Adesta, Erry Yulian Triblas, et al.
Published: (2017)

Comparison of dry and cryogenic machining on chip formation and coefficient of friction in turning AISI 4340 alloy steel
by: A. Raof, Natasha, et al.
Published: (2014)

Thin-walled box beam bending distortion analytical analysis / A Halim Kadarman … [et al.]
by: Kadarman, A Halim, et al.
Published: (2017)

Efficient dressing of the wheel in ELID grinding by controllable voltage with force feed back
by: Saleh, Tanveer, et al.
Published: (2010)

Optical switches for large core diameter optical fibers (POF & PCF)
by: Bhuiyan, Moinul, et al.
Published: (2004)

Disturbance decoupled fault reconstruction using sliding mode observers
by: Kok, Yew Ng, et al.
Published: (2008)

Manufacturing management: from basic machining to quality product
by: Adesta, Erry Yulian Triblas
Published: (2011)

Characterization of fatigue properties of bonded-in pultruded rod timber connection / Zakiah Ahmad and Adiza Jamadin
by: Ahmad, Zakiah, et al.
Published: (2013)

Development of automotive sand casting product (cast iron) with CAE/casting simulation assist / Anizan Hamad @ Ahmad.
by: Hamad @ Ahmad, Anizan
Published: (2009)

Merekabentuk dan menilai peralatan serbaguna untuk ujikaji keseimbangan daya, roda tenaga dan peluncuran
by: Mohd Khathri, Akasyah
Published: (2004)

Q-switched fiber laser employing a passive polarization-maintaining thulium-doped fiber as a saturable absorber
by: Al-Alimi, A.W., et al.
Published: (2022)

A comparative study on image compression method using stand-alone DWT techniques and hybrid of DWT with huffman coding technique for WSN application
by: Hussin, Mumtaz Anwar, et al.
Published: (2002)

Effect of hydraulic pressure on hardness, density, tool wear and surface roughness in the fabrication of alumina based cutting tool
by: M. M., Faiz, et al.
Published: (2018)

Effect of cutting parameters on surface roughness in dry drilling of AISI D2 tool steel by using Taguchi Method
by: M.H. Osman1, M.H. Osman1, et al.
Published: (2018)

Analysis of surface integrity and formation of material side flow in dry and wet machining of aluminum alloy
by: A. B., Hadzley, et al.
Published: (2018)

Physical Properties of New Formulation of Hybrid Nanofluid-based Minimum Quantity Lubrication (MQL) from Modified Jatropha Oil as Metalworking Fluid
by: Sabri, Ainaa Mardhiah, et al.
Published: (2023)

Machinability study on milling kenaf fiber reinforced plastic composite materials using the design of experiments
by: Harun, Azmi, et al.
Published: (2018)

The mold cost estimation calculator for plastic injection mold manufacturing
by: Kamalrudin, massila, et al.
Published: (2008)

Peralatan membaca untuk golongan kurang penglihatan / Fadzli Abd Rahman
by: Fadzli , Abd Rahman
Published: (2000)

Application of fuzzy logic to simulation of rainfall in Kerayong River catchment / Kamsiah Abdul Wahab
by: Abdul Wahab, Kamsiah
Published: (2009)

Development of jig for Coordinate Measuring Machines / Nor Izlan Zulkhiflee
by: Zulkhiflee, Nor Izlan
Published: (2017)

Basic principles and requirements of self compacting concrete / Mohd Syahrul Hisyam Mohd Sani and Ahmad Rasidi Osman
by: Mohd Sani, Mohd Syahrul Hisyam, et al.
Published: (2005)

Effect of volume cavity at various distances for thermal cooling pumping jet device / Aizat Fadzli Ayob
by: Ayob, Aizat Fadzli
Published: (2017)

Modeling plastics injection molding operation using simulation
by: Li Mei, Tan
Published: (2014)

Mold design for plastics injection molding process (two colors) and analysis of gates location
by: Ahmad Zulhelmi, Muhamad
Published: (2009)

The influence of injection molding parameter on properties of thermally conductive plastic
by: Azis, N. Hafizah, et al.
Published: (2017)

Development of thermostable microencapsulated lactobacillus targeted gut delivery / Muhamad Fareez Ismail
by: Ismail, Muhamad Fareez
Published: (2018)

Transport of bed load sediment in the presence of stable clast / Mohd Sofiyan Sulaiman
by: Sulaiman, Mohd Sofiyan
Published: (2016)

3Rs awareness among UiTM Pulau Pinang students / Liza Tajul Aripin
by: Tajul Aripin, Liza
Published: (2005)

Optimization of Glutathione (GSH) from selected Malaysian local fruit by ultrasonic method
by: Arif, Afraha Baiti, et al.
Published: (2010)