Stability analysis of quintuple stellar and planetary systems using a symmetric five-body model

QR Code

Stability analysis of quintuple stellar and planetary systems using a symmetric five-body model

Shoaib [Shoaib, M., 2004. Many body symmetrical dynamical systems. Ph.D. Thesis, eprint arXiv:0709.0652, pp. 132-169] gave an analytical stability criterion for the Caledonian Symmetric Five-Body Problem valid for all time. This analytical stability criterion is verified numerically for the coplanar...

Full description

Bibliographic Details
Main Authors:	M., Shoaib, B. A., Steves, A., Szell
Format:	Article
Language:	English
Published:	ELSEVIER SCIENCE BV, PO BOX 211, 1000 AE AMSTERDAM, NETHERLANDS 2008
Subjects:	TL Motor vehicles. Aeronautics. Astronautics
Online Access:	http://scholars.utp.edu.my/id/eprint/2349/ http://scholars.utp.edu.my/id/eprint/2349/1/SAMPLE_PAPER_PDF.pdf

Similar Items

Frame body structure for solar car
by: Muhamad Izwan, Sunawan
Published: (2010)

Design and analysis of the solar car body
by: Yusri, Yusof
Published: (2010)

Design analysis of exterior car body part
by: Bastian Wibar, Momang
Published: (2013)

Upper body structure design for solar car
by: Muhammad Syafiq, Ayob
Published: (2010)

Aerodynamic study of vehicle drag based on bluff body
by: Mohamad Kamarul, Shamsuddin
Published: (2009)

Two dimensional car body visualization using air flow bench
by: Mohamad Al Rassid, Mohamad Borhanudin
Published: (2008)

Aircraft rigid-body equation of motions: a non linear model
by: Legowo, Ari
Published: (2011)

The application of adhesive bonding for different types of material for car body parts
by: Muhammad Shahir, Nazir
Published: (2013)

Design, analysis and fabricate solar car chasis and body (race type)
by: Muhamad Fikri, Abd Rahman
Published: (2011)

Study of vortex shedding around bluff body using air flow test rig
by: Rafiuddin, Azman
Published: (2008)

Software development for aerodynamic characteristics estimation of wing-body combination of aircraft at cubsonic speeds
by: Dahalan, Md. Nizam, et al.
Published: (2001)

Aerodynamics and Static Stability Characteristics of a Hybrid Buoyant Aerial Vehicle at Low Speed
by: UlHaque, Anwar, et al.
Published: (2015)

Dynamic stability of unguided projectile with 6- DOF trajectory modeling
by: Bashir, Musavir, et al.
Published: (2017)

Experimental and numerical study on the aerodynamics and stability characteristics of a canard aircraft
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2019)

Estimation of stability derivatives of a delta wing in hypersonic flow
by: Crasta, Asha, et al.
Published: (2012)

Implementation of Concurrent Engineering and Analytical Network Process In Manufacturing Process and Material Analysis of Metal Matrix Composites Automotive Component
by: Fatchurrohman, Nanang, et al.
Published: (2014)

Estimating vertical drag on helicopter fuselage during hovering
by: Wahab, A. A., et al.
Published: (2006)

Numerical Study on the Transition Performance of a Scale Model Helicopter from Hovering to Vertical Autorotation
by: Wahab, A. A., et al.
Published: (2006)

Preliminary Experimental Investigation on Autorotation Performance of Scale Model Helicopter in Vertical Manoeuvre
by: Wahab, A. A., et al.
Published: (2006)

Optimised combinatorial control strategy for active anti-roll bar system for ground vehicle
by: Zulkarnain, N., et al.
Published: (2018)

Feasibility Study on Improving of Helicopter Forward Flight Speed via Modification of the Blade Dimension and Engine Performance
by: Nik Mohd., Nik Ahmad Ridhwan, et al.
Published: (2006)

The Development of Autopilot System for an Autonomous UAV Helicopter Model
by: Wahab, A. A., et al.
Published: (2006)

Design and Development of an Experimental Aeroelastic Test Rig
by: Mohd. Rafie, A. S., et al.
Published: (2006)

Structural Optimization of an Aeroelastically Tailored Composite Flat Plate Made of Woven Fiberglass/Epoxy
by: Attaran, A., et al.
Published: (2006)

Mass Fraction Burn Comparison of Compressed Natural Gas and Gasoline
by: D., Ramasamy, et al.
Published: (2014)

Design and fabricate a reer wheel drive differential simulation rig
by: Dinnish, A/L Thegaraju
Published: (2008)

Computational stress and modal analysis of automobile tyre
by: Iskandar Izany, A Rahman
Published: (2008)

Design of revetec engine cam with cycloidal motion profile
by: Khairul Anuar, A. Rahman
Published: (2012)

Electrooculograghy (EOG)-controlled wheelchair
by: Sidek, Shahrul Na'im, et al.
Published: (2011)

The effect of modal properties of crash box structures with trigger mechanisms towards the crashworthiness by using finite element analysis
by: Asri, M. N. A. M., et al.
Published: (2021)

Adaptive sliding mode control for 3dof helicopter
by: Hamood, Mostafa A., et al.
Published: (2011)

Development of polymer-based Y-branch symmetric waveguide coupler using soft lithography technique
by: Ghazali, M. S. M., et al.
Published: (2022)

On The Use of Non uniform inflow Model for Aerodynamics Analysis Helicopter Rotor Blade in the Forward Flight
by: Ghazirah, Ghazirah, et al.
Published: (2006)

The Application of Combined Momentum â€“ Blade Element Theory for Aerodynamics Analysis Helicopter Rotor Blade in the Forward Flight
by: Ghazirah, Ghazirah, et al.
Published: (2006)

Design and analysis of vortex generator for UMP HEV using CFD
by: Wan Mohd Suhaimi, Wan A. Bakar
Published: (2007)

The numerical assessment of motion strategies for integrated linear motor during starting of a free-piston engine generator
by: Mohd Razali, Hanipah, et al.
Published: (2017)

The magnetorheological fluid: testing on automotive braking system
by: Zainordin, A. Z., et al.
Published: (2021)

Preliminary design of carbon composite facing for dry clutch disc of mini agricultural tractor
by: Munir, F.A, et al.
Published: (2011)

Flowfield-dependent variant method for moving-boundary problems
by: Zulkafli, Mohd Fadhli, et al.
Published: (2014)

Study of base pressure behavior in a suddenly expanded duct at supersonic mach number regimes using statistical analysis
by: Quadros, Jaimon Dennis, et al.
Published: (2018)