Effect of high-speed parameters on uncoated carbide tool
in finish turning titanium Ti-6Al-4V ELI

QR Code

Effect of high-speed parameters on uncoated carbide tool in finish turning titanium Ti-6Al-4V ELI

In this work, the Sandvik uncoated carbide insert, CNGG 120408-SGF-H13A was used as a cutting tool in high-speed turning of titanium alloy Ti-6Al-4V ELI (extra-low interstitial) with hardness of 32 HRC. Wear is one of the problems that cannot be avoided in machining process. Therefore, the objective...

Full description

Bibliographic Details
Main Authors:	Sulaiman, M.A., Che Haron, C.H., Ghani, J.A., Kasim, M.S.
Format:	Article
Language:	English
Published:	Universiti Kebangsaan Malaysia 2014
Online Access:	http://journalarticle.ukm.my/6822/ http://journalarticle.ukm.my/6822/1/14_M.A._Sulaiman.pdf

Similar Items

Performance evaluation of uncoated carbide tool in high speed drilling of Ti6Al4V
by: Abd. Rahim, Erween, et al.
Published: (2008)

Performance of coated- and uncoated-carbide tools when drilling titanium alloy—Ti–6Al4V
by: Sharif, Safian, et al.
Published: (2007)

The performance of uncoated tungsten carbide insert in end milling titanium alloy Ti-6Al 4V through work piece preheating
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Development of surface roughness models in end milling titanium alloy Ti-6Al-4V using uncoated tungsten carbide inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Tool life prediction by response surface methodology for end milling titanium alloy ti–6al–4v using uncoated carbide inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2007)

Comparative study between wear of uncoated and TiAlN-coated carbide tools in milling of Ti6Al4V
by: Uddin, M., et al.
Published: (2017)

Assessment of performance of uncoated and coated carbide inserts in end milling of Ti-6Al-4V through modelling
by: Hossain, Ishtiaq, et al.
Published: (2011)

Comparison of uncoated and coated carbide inserts in end milling of Ti–6Al–4V in terms of surface roughness
by: Hossain, Mohammad Ishtiaq, et al.
Published: (2008)

The effectiveness of floor finishes in shopping centers / Elis Suzana Muhamad
by: Muhamad, Elis Suzana
Published: (2001)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
by: Abd. Rahim, Erween
Published: (2005)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
by: Abd. Rahim, Erween
Published: (2005)

Effect of high speed dry end milling on surface roughness and cutting forces of Ti-6Al-4V ELI
by: Sharif, S., et al.
Published: (2014)

Cutting force and surface roughness characterization in cryogenic high-speed end milling of Ti-6Al-4V ELI
by: Safari, H., et al.
Published: (2014)

Effect of drill geometry of uncoated tool when drilling titanium alloy, Ti-6Al-4V
by: Rashiddy Wong, Freddawati
Published: (2008)

Modeling for surface roughness in end-milling of Titanium alloy Ti-6Al-4V using uncoated WC-Co inserts
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Tool life of TiAlN PVD coated carbide tool in high-speed end milling of untreated inconel 718 under minimum quantity lubrication condition
by: Kasim, M.S., et al.
Published: (2013)

Wear Mechanism of Coated and Uncoated Carbide Cutting Tool in Machining Process
by: J. A., Ghani, et al.
Published: (2016)

Optimization of the surface roughness for titanium Ti6A14V in turning process using Taguchi method
by: Samin, R., et al.
Published: (2020)

Modeling for surface roughness in end-milling of titanium alloy Ti-6AI-4V using uncoated WC-Co and PCD Inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2007)

Progressive tool wear in machining biomedical alloy using uncoated and titanium diboride coated tungsten carbide tools
by: Mohd Hafizu, Zakaria
Published: (2019)

Effect of cooling methods on dimensional accuracy and surface finish of a turned titanium part
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Comparison of surface roughness in end milling of titanium alloy Ti-6Al-4V using uncoated WC-Co and PCD inserts through generation of models
by: Ginta, Turnad Lenggo, et al.
Published: (2011)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Tool life prediction by response surface methodology in end milling titanium alloy Ti-6Al-4V using uncoated WC-Co inserts
by: Turnad, L. Ginta, et al.
Published: (2009)

The use of TiAIN coated carbide tool when finish machining hardened stainless steel
by: Noordin, M. Y., et al.
Published: (2007)

Crystallinity, surface morphology, and chemical composition of the recast layer and rutile-TiO2 formation on Ti-6Al-4V ELI by wire-EDM to enhance biocompatibility
by: Rahman, S., et al.
Published: (2017)

Tool life prediction by response surface methodology in end milling titanium alloy Ti-6A1-4V using uncoated WC-Co inserts
by: Turnad L., Ginta, et al.
Published: (2009)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

High speed machining of titanium alloy, Ti6Al4V to achieve nano level surface roughness
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

An Investigation of Surface Finish in Dry Turning
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Studies on Tensile Properties of Titanium Carbide (TiC) Particulates Composites
by: Suraya, Sulaiman, et al.
Published: (2014)

Studies on tensile properties of titanium carbide (TiC) particulates composites
by: Sulaiman, Suraya, et al.
Published: (2014)

Performance of uncoated WC-Co in end milling of Aluminium Silicon Carbide (AlSiC)
by: M. K. , Nor Khairusshima, et al.
Published: (2011)

Optimization of surface roughness in high speed end milling of Titanium alloy Ti-6Al-4V under dry conditions
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Performance of coated and uncoated carbide tools while dry machining aluminium alloy
by: Amin Abidin, Buran
Published: (2010)

Effect of high speed end milling of Co-28Cr-6Mo cobalt chromium molybdenum alloy using uncoated and coated carbide tools
by: Zaman, H., et al.
Published: (2017)

Flank Wear Characterization in Aluminum Alloy (6061 T6) with Nanofluid MQL Environment using Uncoated Carbide Tool
by: Najiha, M. S., et al.
Published: (2015)

Effect of carburization process on adhesion strength of ti carbide layer on titanium alloy substrate
by: Sudin, Izman, et al.
Published: (2011)

Effectiveness of uncoated WC-Co and PCD inserts in end milling of aluminum silicon carbide (AlSiC)
by: M. K., Nor Khairusshima, et al.
Published: (2007)

Finite element simulation of machining AISI 1045 steel using uncoated carbide tool
by: Mohmd Arifin, Nabila Afif
Published: (2012)