Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites
This paper reports on the effects of HAP addition and sintering temperature on the microstructure and properties of the F-75/HAP composites fabricated by powder metallurgy. Co-Cr-Mo (F-75) is used in orthopedics because of its excellent biocompatibility when implanted to human or animal body. Hydrox...
| Main Authors: | , , |
|---|---|
| Format: | Article |
| Language: | English |
| Published: |
Universiti Kebangsaan Malaysia
2013
|
| Online Access: | http://journalarticle.ukm.my/6687/ http://journalarticle.ukm.my/6687/1/11_Nur_Maizatul_Shima.pdf |
| _version_ | 1848811234497921024 |
|---|---|
| author | Nur Maizatul Shima Adzali, Shamsul Baharin Jamaludin, Mohd Nazree Derman, |
| author_facet | Nur Maizatul Shima Adzali, Shamsul Baharin Jamaludin, Mohd Nazree Derman, |
| author_sort | Nur Maizatul Shima Adzali, |
| building | UKM Institutional Repository |
| collection | Online Access |
| description | This paper reports on the effects of HAP addition and sintering temperature on the microstructure and properties of the F-75/HAP composites fabricated by powder metallurgy. Co-Cr-Mo (F-75) is used in orthopedics because of its excellent biocompatibility when implanted to human or animal body. Hydroxyapatite (HAP) powders have been used as fillers because HAP is the one of the most effective biocompatible materials with similarities to mineral constituents of bones and teeth. HAP powders (chemical formula Ca10(PO4)6 (OH)2) have been added to Co-Cr-Mo alloys in composition of 0 to 10 wt. %. The mixtures were then milled, cold compacted at 550 MPa, before sintered at 1100 and 1200°C in a tube furnace. The density, porosity, microhardness and compressive strength were measured. The composites that have been sintered at temperature 1200°C showed better physical and mechanical properties than those produced at 1100°C. After sintering at 1200°C, the samples show higher density, compared with the sample sintered at 1100°C. The sample with no HAP which have been sintered at 1200°C has the highest microhardness (208.9 HV), compared with the same sample sintered at 1100°C (194.3HV). As the temperature is increased from 1100 to 1200°C, the value of compressive strength increased from 184.538 to 341.086 MPa. Microstructural analysis for line scan showed that, as the sintering temperature was increased, there was good interface bonding between HAP particles and matrix F-75. |
| first_indexed | 2025-11-14T23:43:10Z |
| format | Article |
| id | oai:generic.eprints.org:6687 |
| institution | Universiti Kebangasaan Malaysia |
| institution_category | Local University |
| language | English |
| last_indexed | 2025-11-14T23:43:10Z |
| publishDate | 2013 |
| publisher | Universiti Kebangsaan Malaysia |
| recordtype | eprints |
| repository_type | Digital Repository |
| spelling | oai:generic.eprints.org:66872016-12-14T06:41:55Z http://journalarticle.ukm.my/6687/ Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites Nur Maizatul Shima Adzali, Shamsul Baharin Jamaludin, Mohd Nazree Derman, This paper reports on the effects of HAP addition and sintering temperature on the microstructure and properties of the F-75/HAP composites fabricated by powder metallurgy. Co-Cr-Mo (F-75) is used in orthopedics because of its excellent biocompatibility when implanted to human or animal body. Hydroxyapatite (HAP) powders have been used as fillers because HAP is the one of the most effective biocompatible materials with similarities to mineral constituents of bones and teeth. HAP powders (chemical formula Ca10(PO4)6 (OH)2) have been added to Co-Cr-Mo alloys in composition of 0 to 10 wt. %. The mixtures were then milled, cold compacted at 550 MPa, before sintered at 1100 and 1200°C in a tube furnace. The density, porosity, microhardness and compressive strength were measured. The composites that have been sintered at temperature 1200°C showed better physical and mechanical properties than those produced at 1100°C. After sintering at 1200°C, the samples show higher density, compared with the sample sintered at 1100°C. The sample with no HAP which have been sintered at 1200°C has the highest microhardness (208.9 HV), compared with the same sample sintered at 1100°C (194.3HV). As the temperature is increased from 1100 to 1200°C, the value of compressive strength increased from 184.538 to 341.086 MPa. Microstructural analysis for line scan showed that, as the sintering temperature was increased, there was good interface bonding between HAP particles and matrix F-75. Universiti Kebangsaan Malaysia 2013-12 Article PeerReviewed application/pdf en http://journalarticle.ukm.my/6687/1/11_Nur_Maizatul_Shima.pdf Nur Maizatul Shima Adzali, and Shamsul Baharin Jamaludin, and Mohd Nazree Derman, (2013) Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites. Sains Malaysiana, 42 (12). pp. 1763-1768. ISSN 0126-6039 http://www.ukm.my/jsm/ |
| spellingShingle | Nur Maizatul Shima Adzali, Shamsul Baharin Jamaludin, Mohd Nazree Derman, Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites |
| title | Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites |
| title_full | Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites |
| title_fullStr | Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites |
| title_full_unstemmed | Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites |
| title_short | Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites |
| title_sort | effect of sintering on the physical and mechanical properties of co-cr-mo (f-75)/hap composites |
| url | http://journalarticle.ukm.my/6687/ http://journalarticle.ukm.my/6687/ http://journalarticle.ukm.my/6687/1/11_Nur_Maizatul_Shima.pdf |