Comparative study of gearbox fault diagnosis by vibration measurements

QR Code

Comparative study of gearbox fault diagnosis by vibration measurements

Vibration analysis has been demonstrated to be one of the best tools to detect faults in a gearbox by providing abundant information about the operating condition of a gearbox. However, a gearbox generates complex vibration signals, which makes it difficult to diagnose when a fault occurs. There are...

Full description

Bibliographic Details
Main Authors:	Hartono, Dennis, Halim, Dunant, Widodo, Achmad, Roberts, Gethin Wyn
Format:	Article
Published:	EDP Sciences 2016
Online Access:	https://eprints.nottingham.ac.uk/47196/

Similar Items

Bevel gearbox fault diagnosis using vibration measurements
by: Hartono, Dennis, et al.
Published: (2016)

Vibration-based fault diagnostic of a spur gearbox
by: Hartono, Dennis, et al.
Published: (2016)

Time-frequency enhancement technique for bevel gear fault diagnosis
by: Hartono, Dennis, et al.
Published: (2016)

Artificial neural network-based fault diagnosis of gearbox using empirical mode decomposition from vibration response
by: Mutra, R. R., et al.
Published: (2023)

The Development of Lumped Mass Dynamic Modeling Methods of Planetary Gearbox for Fault Detection and Diagnosis
by: Wang, Zhongwei, et al.
Published: (2010)

Qualitative study of riccati difference equation on maneuvering target tracking and fault diagnosis of wind turbine gearbox
by: Sumathy, M., et al.
Published: (2019)

Vibration-based multi-fault diagnosis for centrifugal pumps
by: Kamiel, Berli Paripurna
Published: (2015)

Vibration Faults Simulation System (VFSS): A System for teaching and training on fault detection and diagnosis
by: Abdul Muthalif, Asan Gani, et al.
Published: (2002)

Real time on-the-fly kinematic GPS
by: Roberts, Gethin Wyn
Published: (1997)

Diagnosis of blade fault based on wavelet scalogram and blade pass vibration signature analysis
by: Lim, Meng Hee, et al.
Published: (2015)

Study on the development of electromagnetic two speed gearbox for EV
by: Rahman, Mohammed Ataur, et al.
Published: (2019)

Application of CFD to model an aeroengine internal gearbox
by: Turner, Adam James
Published: (2015)

Design and fabricate a speed reducer gearbox
by: Mohd Arif, Mohd Ariffin
Published: (2008)

Correlated GNSS and temperature measurements at 10-minute intervals on the Severn Suspension Bridge
by: Roberts, Gethin Wyn, et al.
Published: (2017)

Temperature effects on the vertical movements of the Severn Suspension Bridge’s suspension cables measured by GNSS
by: Roberts, Gethin Wyn, et al.
Published: (2016)

Vibration sensor placement for delamination detection in a beam structure based on the vibration-based chaotic oscillator method
by: Li, Xuan, et al.
Published: (2020)

Control of vibration using compliant actuators
by: Mareta, Sannia, et al.
Published: (2017)

Condition Monitoring Techniques of the Wind Turbines Gearbox and Rotor
by: Salem, A., et al.
Published: (2014)

Fuzzy logic controller for an automatic car gearbox shifting
by: Norafiza, Mohd Hassim
Published: (2009)

The use of PSD analysis on BeiDou and GPS 10Hz dynamic data for change detection
by: Roberts, Gethin Wyn, et al.
Published: (2016)

Correlation of the movements of the Severn Suspension Bridge derived with GNSS with temperature variations
by: Roberts, Gethin Wyn, et al.
Published: (2016)

Multi-frequency approach to fault dictionary of linear analog fault diagnosis
by: Chandra Babu, N. Sarat, et al.
Published: (2008)

Vibration absorption performance of membrane-type metamaterial on a thin plate
by: Gao, Cong, et al.
Published: (2019)

Measurement signal quality assessment on all available and new signals of multi-GNSS (GPS, GLONASS, Galileo, BDS, and QZSS) with real data
by: Quan, Yiming, et al.
Published: (2016)

A study of tribological aspects in gearbox of CNG engine / Abdul Hakim Ahmad
by: Ahmad, Abdul Hakim
Published: (2010)

Relative shaft displacement and vibration measurements for the early fault detection in rolling element bearing
by: Leo, Sing Lim.
Published: (2004)

Adaptive Case Based Reasoning for Fault Diagnosis
by: Pang, Shen Yee, et al.
Published: (2009)

Fault detection and diagnosis methods for engineering systems
by: Vileiniskis, Marius
Published: (2015)

Fault detection and diagnosis using correlation coefficients
by: Mak, Weng Yee
Published: (2005)

Application of Order Analysis to Diagnose Fatigue within Wind Turbine Gearbox
by: Salem, A., et al.
Published: (2017)

A review of condition monitoring techniques of the wind turbines gearbox and rotor
by: Salem, Abdulwahed, et al.
Published: (2013)

Forced vibration analysis of a fibre-reinforced polymer laminated beam using the green function method
by: Li, Xuan, et al.
Published: (2020)

Blade fault diagnosis using artificial intelligence technique
by: W. K., Ngui
Published: (2016)

Neural networks applied for fault diagnosis of AC motors
by: K.S., Rama Rao, et al.
Published: (2008)

Neural Networks based fault diagnosis of ac motors
by: K.S., Rama Rao, et al.
Published: (2008)

Machinery fault diagnosis using advanced correlation filters
by: Loo, C. K., et al.
Published: (2007)

Machinery fault diagnosis using advanced correlation filters
by: Loo, C. K., et al.
Published: (2007)

Open circuit fault detection and diagnosis in matrix converters
by: Brunson, C., et al.
Published: (2014)

Kernel-based fault diagnosis on mineral processing plants
by: Gorden, T., et al.
Published: (2006)

A review of satellite positioning systems for civil engineering
by: Roberts, Gethin Wyn, et al.
Published: (2015)