Study on lattice structures using additive manufacturing and its application on a new ultra-lightweight vehicle suspension system

QR Code

Study on lattice structures using additive manufacturing and its application on a new ultra-lightweight vehicle suspension system

With the increasing development of Additive Manufacturing technologies in the past two decades, the area of lattice structures has received considerable attention due to their inherent advantages in providing lightweight, high stiffness, and strong materials. However, this comes with new challenges...

Full description

Bibliographic Details
Main Author:	Niu, Jie
Format:	Thesis (University of Nottingham only)
Language:	English
Published:	2017
Subjects:	Lattice structures; Additive manufacturing
Online Access:	https://eprints.nottingham.ac.uk/46690/

Similar Items

Compressive failure modes and energy absorption in additively manufactured double gyroid lattices
by: Maskery, Ian, et al.
Published: (2018)

Strategies for functionally graded lattice structures derived using topology optimisation for additive manufacturing
by: Panesar, Ajit, et al.
Published: (2018)

Design of mechanically-optimised lattice structures for vibration isolation
by: Syam, Wahyudin P., et al.
Published: (2017)

Design and analysis of strut-based lattice structures for vibration isolation
by: Syam, Wahyudin P., et al.
Published: (2017)

Analytical solution and experimental study of effective Young’s modulus of SLM-fabricated lattice structure with triangular unit cells
by: Niu, Jie, et al.
Published: (2018)

Finite element analysis and experimental study of plastic lattice structures manufactured by selective laser sintering
by: Sun, Wei, et al.
Published: (2017)

Investigation of PBF-LB stainless steels and lattice structures for crashworthiness applications
by: Della Crociata, Diego
Published: (2025)

Analysis of defects in additively manufactured lattice structures
by: Echeta, Ifeanyichukwu
Published: (2023)

Numerical study on load-bearing capabilities of beam-like lattice structures with three different unit cells
by: Niu, Jie, et al.
Published: (2017)

Insights into the mechanical properties of several triply periodic minimal surface lattice structures made by polymer additive manufacturing
by: Maskery, Ian, et al.
Published: (2017)

Design optimization for an additively manufactured automotive component
by: Abdi, Meisam, et al.
Published: (2018)

Mechanical properties of Ti-6Al-4V selectively laser melted parts with body-centred-cubic lattices of varying cell size
by: Maskery, Ian, et al.
Published: (2015)

Additively manufactured lattice structures for vibration attenuation
by: Elmadih, Waiel
Published: (2020)

Thermofluid optimisation of additive manufacturing high heat flux components for fusion
by: Padrao, Daniel
Published: (2024)

Thermal properties of lattice structures by laser powder bed fusion for aerospace systems
by: SÉLO, Richard Roger Joachim
Published: (2022)

A mechanical property evaluation of graded density Al-Si10-Mg lattice structures manufactured by selective laser melting
by: Maskery, Ian, et al.
Published: (2016)

An investigation into reinforced and functionally graded lattice structures
by: Maskery, Ian, et al.
Published: (2016)

Applications of coherence scanning interferometry in additive manufacturing
by: Gomez Moreno, Carlos Alberto
Published: (2022)

Detection and characterization of in-service damage in lattice structures using ultrasonics
by: Tarar, Hasan
Published: (2025)

Band gap behavior of optimal one-dimensional composite structures with an additive manufactured stiffener
by: Ampatzidis, Theofanis, et al.
Published: (2018)

A voxel-based method of constructing and skinning conformal and functionally graded lattice structures suitable for additive manufacturing
by: Aremu, Adedeji, et al.
Published: (2016)

Machining of additively manufactured parts: implications for surface integrity
by: Oyelola, Olusola, et al.
Published: (2016)

The Impact of Additive Manufacturing on the Innovation Process of the Sports Equipment Industry
by: Meier, Marlon
Published: (2017)

Laser powder bed fusion of lattice structures for thermomechanical applications
by: Catchpole-Smith, Sam
Published: (2020)

A cost model of part consolidation for additive manufacturing
by: Stevenson, Alicia
Published: (2018)

Mesoscale additively manufactured flow reactors for synthetic, crystallisation and biocatalytic applications
by: Okafor, Obinna
Published: (2020)

Upscaled Lattice Boltzmann Method for simulations of flows in heterogeneous porous media
by: Jun, Li, et al.
Published: (2017)

Measurement of internal surfaces of additively manufactured parts by X-ray computed tomography
by: Thompson, Adam, et al.
Published: (2017)

Additive manufacturing of mitral annuloplasty devices
by: Blake, Charlotte
Published: (2021)

Additive manufacturing in Australian small to medium enterprise: Vat polymerisation techniques, case study and pathways to Industry 4.0 competitiveness
by: Rooney, Kimberley, et al.
Published: (2023)

The impact of adopting Additive Manufacturing on responsive supply chain performance
by: Alogla, Ageel
Published: (2021)

Review of post-process optical form metrology for industrial-grade metal additive manufactured parts
by: Stavroulakis, P.I., et al.
Published: (2016)

Cryptanalysis of RSA and its variants using continuous midpoint subdivision analysis and lattices
by: Wan Mohd Ruzai, Wan Nur Aqlili
Published: (2021)

Investigations into glass additive manufacturing by selective laser melting and directed energy deposition
by: Spirrett, Fiona
Published: (2021)

X-ray computed tomography for additive manufacturing: a review
by: Thompson, Adam, et al.
Published: (2016)

Towards in-process inspection of additive manufacturing using laser ultrasonics
by: Pieris, Don
Published: (2022)

Coherence scanning interferometry for additive manufacture
by: Gomez, Carlos, et al.
Published: (2017)

Design framework for multifunctional additive manufacturing: coupled optimization strategy for structures with embedded functional systems
by: Panesar, Ajit, et al.
Published: (2017)

X-ray computed tomography and additive manufacturing in medicine: a review
by: Thompson, Adam, et al.
Published: (2017)

Additive manufacturing of phosphate glass / polylactic acid composites for biomedical application
by: He, Lizhe
Published: (2021)