Novel stiffeners exploiting internal pressurisation to enhance buckling behaviour under bending loads

QR Code

Novel stiffeners exploiting internal pressurisation to enhance buckling behaviour under bending loads

The paper proposes a novel type of stiffener designed to bear bending loads by exploiting internal pressure effects. The stiffener is made of two adjacent thin-walled pipes (r/t≥50) jointed with a connecting strip. Such a structure is shown to have higher performance against buckling failure compare...

Full description

Bibliographic Details
Main Authors:	Polenta, Valerio, Garvey, Seamus D., Chronopoulos, Dimitrios, Long, Andy C., Morvan, Herve
Format:	Article
Published:	Elsevier 2016
Subjects:	Buckling; internal pressure; pure bending; thin-walled shell
Online Access:	https://eprints.nottingham.ac.uk/33599/

Similar Items

Exploiting internal pressurisation to enhance structural properties
by: Polenta, Valerio
Published: (2017)

Quantitative characterization of the interfacial adhesion of Ni thin film on steel substrate: a compression-induced buckling delamination test
by: Zhu, W., et al.
Published: (2015)

A new model based on evolutionary computing for predicting ultimate pure bending of steel circular tubes
by: Shahin, Mohamed, et al.
Published: (2014)

Eigen-transitions in cantilever cylindrical shells subjected to vertical edge loads
by: Coman, Ciprian D., et al.
Published: (2018)

Influence of stiffener on aluminium perforated plates subjected to in-plane shear loading
by: Hassan, Mohd Nizam
Published: (2018)

Finite element implementation of Koiter's initial post-buckling analysis
by: Yan, Jiayi
Published: (2019)

Improving buckling and post-buckling of shape memory alloy laminated composite plates subjected to mechanical and thermal loading using finite element method
by: A.Rasid, Zainudin
Published: (2012)

On the characterisation of polar fibrous composites when fibres resist bending
by: Soldatos, Konstantinos
Published: (2017)

Bending properties of finger jointed Mahang Gajah (macaranga gigantae) / Muhammad Dhiyauddin Kamaruzaman
by: Kamaruzaman, Muhammad Dhiyauddin
Published: (2016)

Buckling and post-buckling of steel box section using finite element method
by: Isham, Nur Hazwani
Published: (2021)

Strains, deformations and buckling in very thin torispherical pressure vessel ends
by: Campbell, T.D.
Published: (1975)

Bending Performance of I-Joists from Jointed Oriented Strand Board (OSB) Web and Laminated Veneer Lumber (LVL) Flanges
by: Wan Abdul Rahman, Wan Mohd Nazri
Published: (2000)

Modal nudging in nonlinear elasticity: tailoring the elastic post-buckling behaviour of engineering structures
by: Cox, B.S., et al.
Published: (2018)

Bending properties of Mahang Gajah (macaranga gigantea) by using destructive and non-destructive testing / Nur Aini Zul Bakri
by: Zul Bakri, Nur Aini
Published: (2016)

Impact of Buckling Deformation on the FRA Signature of Power Transformer
by: Amini, Arman, et al.
Published: (2013)

Origami pattern parameter modelling of thin-walled structure during axial crushing
by: Abu Mansor, Siti Marhainis
Published: (2020)

Acoustic transmission properties of pressurised and pre-stressed composite structures
by: Ampatzidis, Theofanis, et al.
Published: (2016)

Wave propagation in pressurised composite structures with frequency band gap behaviour
by: Ampatzidis, Theofanis, et al.
Published: (2016)

Parametric study of control of frequency banded behaviour of periodic pressurised composite structures
by: Ampatzidis, Theofanis, et al.
Published: (2017)

Bending behaviour of dowelled mortise and tenon joints in Kempas / Rohana Hassan, Azmi Ibrahim and Zakiah Ahmad
by: Hassan, Rohana, et al.
Published: (2008)

A coupled 1D film hydrodynamics and core gas flow model for air-oil flows in aero-engine bearing chambers
by: Kakimpa, Bruce, et al.
Published: (2017)

Transitional two-phase flow around 90° bends of different orientations
by: Omar, Rajab Abulgasem
Published: (2017)

Geopolymer Concrete Columns under Combined Axial Load and Biaxial Bending
by: Rahman, Muhammad, et al.
Published: (2011)

Experimental and computational fluid dynamics (CFD) studies of gas-liquid flow in bends
by: Abdulkadir, Mukhtar.
Published: (2011)

Finite element analysis of buckling of composite-stiffened panels
by: Zaighami, Arash
Published: (2014)

Predicting the broadband response of a layered cone-cylinder-cone shell
by: Chronopoulos, Dimitrios, et al.
Published: (2014)

The control and maintenance of desired flow patterns in bends of different orientations
by: Zhao, D., et al.
Published: (2016)

Reducing weight and fuel consumption of civil aircraft by electromagnetic launch
by: Bertola, Luca, et al.
Published: (2017)

Cylindrical shell hybrid finite elements
by: Edwards, Gordon
Published: (1974)

Finite Element Analysis of Spring Back Phenomenon in V- bending of Sheet Metals
by: Imhemed, Ramadan Muftah
Published: (2004)

On design and simulation of passive damping solutions for milling of thin-walled parts
by: Kolluru, Kiran V.S.S.
Published: (2015)

Boundary control of marine risers with bending couplings
by: Nguyen, T., et al.
Published: (2012)

Effects of Initial Moisture Content on Boil Bending Properties of Solid Rubberwood (Hevea Brasiliensis)
by: Choo, Koh Boon
Published: (2001)

Quasi-Static Axial Crushing Behaviour of Composite Hemi-Spherical Shells
by: Saleh, Mhfud Ahmed Masoud
Published: (2004)

A cantilever approach to estimate bending stiffness of buildings affected by tunnelling
by: Haji, Twana, et al.
Published: (2018)

Controlling aero-elastic instability of curtain wall systems in high-rise buildings
by: Tan, Ben Hoea, et al.
Published: (2011)

Neural Network Model and Finite Element Simulation of Spring back in Plane-Strain Metallic Beam Bending
by: Abu Khadra, Fayiz Y. M.
Published: (2006)

Wave interaction with defects in pressurised composite structures
by: Apalowo, R.K., et al.
Published: (2018)

Modeling for preliminary analysis of core wall / Noorul Azmah Abdul Aziz
by: Abdul Aziz, Noorul Azmah
Published: (2006)

Bridging the GUI gap with reactive values and relations
by: Perez, Ivan, et al.
Published: (2015)