Topology Optimization of an Engine Mounting Bracket

QR Code

Topology Optimization of an Engine Mounting Bracket

Engine mounting system is an essential component to a vehicle in providing the isolation of vibration and noise which are generated by the engine. While various system designs have been studied for improvements, less attention were given to study the effects of vibrational load to subcomponents...

Full description

Bibliographic Details
Main Authors:	M.I.N, Ma'arof, H., Husain, J.B., Saedon, N.H.M, Nor, M.S., Meo, Girma, T. Chala, Muhammad, Abdul Wahab
Format:	Article
Published:	International Journal of Emerging Technology and Advanced Engineering 2022
Subjects:	T Technology (General) TA Engineering (General). Civil engineering (General) TJ Mechanical engineering and machinery
Online Access:	http://eprints.intimal.edu.my/1650/

Similar Items

Mounting bracket
by: Sahari, Barkawi
Published: (2009)

Trends in an increased dependence towards hydropower energy utilization — a short review
by: Girma, T. Chala, et al.
Published: (2019)

Optimization of engine mounting bracket location
by: Ilyas, Ishak
Published: (2008)

Influence of Aluminum Mesh electrode on Performance of a Microbial Fuel Cell (MFC)
by: M.I.N, Ma'arof, et al.
Published: (2018)

Influence of fins designs, geometries and conditions on the performance of a plate-fin heat exchanger-experimental perspective
by: M.I.N, Ma'arof, et al.
Published: (2019)

Performance Analysis of Turbine Ventilators for Refugee Camps Usage
by: M.I.N, Ma'arof, et al.
Published: (2019)

Analysis and Optimization of an Aftermarket Intercooler Spray‟s Nozzle
by: M.I.N, Ma'arof, et al.
Published: (2022)

A COMPARATIVE STUDY OF ELECTRICITY GENERATION FROM INDUSTRIAL WASTEWATER THROUGH MICROBIAL FUEL CELL
by: M.I.N, Ma'arof, et al.
Published: (2020)

Anti-Lift Assessment of Multi-Flap Motorcycle Winglet for Track Usage Via Wind Tunnel Test
by: M.I.N, Ma'arof, et al.
Published: (2022)

A study on microbial fuel cell (MFC) with graphite electrode to power underwater monitoring devices
by: Ma'arof M.I.N., M.I.N, et al.
Published: (2018)

A study on the performance analysis of bioethanol produced from sugarcane molasses in SI engine
by: M.I.N, Ma'arof*, et al.
Published: (2020)

Elemental and microstructural analysis of fake, real, and standard orthodontic brackets
by: S. H., Nasir, et al.
Published: (2018)

Performance Analysis of Blended Tyre Pyrolysis Oil (TPO) Against Diesel in A YANMAR TF-120 Single Cylinder Diesel Engine
by: Lim, Jin Wei, et al.
Published: (2022)

The development of an aftermarket intercooler spray for turbocharged vehicles using ethylene glycol and hyaluronic acid
by: M.I.N, Ma'arof, et al.
Published: (2020)

SMART METERING DEVICE FOR HVAC SYSTEM
by: Maarof, M.I, et al.
Published: (2018)

Injection of non-reacting gas into production pipelines to ease restart pumping of waxy crude oil
by: T. Chala, Girma
Published: (2017)

Development of an after-market universal fuel gauge for motorcycle
by: Maarof, M.I, et al.
Published: (2018)

Vibration analysis of vehicle engine mounting
by: Teh, Swee Ing
Published: (2013)

A Study on Separation Efficiency of Multiphase Desander
by: Arwinder Singh, Jigiri Singh, et al.
Published: (2022)

Potential utilization of biodiesel as alternative fuel for compression ignition engine in Malaysia
by: Wahab, M. A.*, et al.
Published: (2017)

A Study on Extraction Pipe Insulation for Solidification Prevention of Heavy Crude Oil after Extraction
by: Arwinder Singh, Jigiri Singh, et al.
Published: (2023)

A Study on Multiple Load Conditions Analysis for a Conventional Bicycle vs. a Variable-Chain Stay-Length (VCL) Bicycle De1
by: Meor Rashydan, Abdullah, et al.
Published: (2023)

Development of a Self-Contained Power Management System
by: R., Jeyagopi, et al.
Published: (2022)

Selection of A Roll Cage Assembly for The FSAE Racing Car Via Priority and Design Matrix
by: Muhammad Izzat Nor, Ma'arof, et al.
Published: (2020)

Assessment of FSAE Car’s Rear Suspension Arms for Bump Force
by: Muhammad Izzat Nor, Ma'arof, et al.
Published: (2022)

A Study on Multiple Load Conditions Analysis for a Bicycle Chassis
by: Choo, Wou Onn, et al.
Published: (2022)

Exhaust Manifold Assessment for Backpressure Minimization
by: Muhammad Izzat Nor, Ma'arof, et al.
Published: (2023)

A Study on the Development of the Make-shift Heat Pump for Refugee Camp: A Case Study of Borneo State, Nigeria
by: Muhammad Izzat Nor, Ma'arof, et al.
Published: (2019)

The Development of an Aftermarket Intercooler Spray for Turbocharged Vehicles using Water
by: Muhammad Izzat Nor, Ma'arof, et al.
Published: (2019)

Effect of Pot Size in Soil Heat Transfer
by: Mohamad Fariz, Mohamed Nasir*, et al.
Published: (2022)

Computational Fluid Dynamic Analysis to determine Downforce of Motorcycle Winglet
by: Mohd Amir Shazwan, Hashim, et al.
Published: (2020)

Design Metal Detecting Arduino Remote Control Robot Vehicle Controlled via Bluetooth
by: R., Jeyagopi, et al.
Published: (2022)

Roll-Cage’s Hollow-Tubing Specification Assessment for an Off-Road Buggy
by: Mohd Amir Shazwan, Hashim, et al.
Published: (2023)

Transfer of Technology for Tactical Floating Bridge Local Fabrication
by: Mohamad Fariz, Mohamed Nasir*, et al.
Published: (2023)

Fatigue analysis of Package Terminal Air Conditioner motor bracket under dynamic loading
by: Loh, S.K., et al.
Published: (2009)

Design and development of a 2 Degree of Freedom 3D Printed Myoelectric Prosthetic Arm to Sustain High Load for Amputees
by: Muhammad Izzat Nor, Ma'arof, et al.
Published: (2019)

Applications of Digital Photogrammetric Systems for Dimensional Measurement and 3D Modelling
by: Setan, Halim, et al.
Published: (2004)

A Short Review on Factors that Impact the Backpressure of exhaust manifold of spark ignition engine
by: Muhammad Izzat Nor, Ma'arof, et al.
Published: (2019)

Topology Optimization of Truss Structures
by: Koh, Boon Chuen
Published: (2019)

Secure topology for electronic medical record transmission
by: Alanazi, Hamdan O., et al.
Published: (2010)