The implementation of Taguchi method on EDM process of Tungsten Carbide

QR Code

The implementation of Taguchi method on EDM process of Tungsten Carbide

In this paper, the cutting of Tungsten Carbide ceramic using electro-discharge machining (EDM) with a graphite electrode by using Taguchi methodology has been reported. The Taguchi method is used to formulate the experimental layout, to analyse the effect of each parameter on the machining character...

Full description

Bibliographic Details
Main Authors:	Lajis, Mohd Amri, Che Daud, Mohd Radzi, Amin, A. K. M. Nurul
Format:	Article
Language:	English
Published:	EuroJournals Publishing, Inc. 2009
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/914/ http://irep.iium.edu.my/914/1/The_Implementation_of_Taguchi_Method_on_EDM_Process_of.pdf

Similar Items

The implementation of Taguchi method on EDM process of tungsten carbide
by: Lajis, Mohd Amri, et al.
Published: (2009)

Study on surface integrity of tungsten carbide macidned by die-sinking EDM using Taguchi method / Amizan Amran
by: Amran, Amizan
Published: (2009)

Analysis of the Influence of EDM Parameters on Surface Quality, Material Removal Rate and Electrode Wear of Tungsten Carbide
by: Siti Haryani, Tomadi, et al.
Published: (2009)

Optimization of micro EDM drilling process using Taguchi method
by: Yazid, Yahya
Published: (2009)

Analysis and simulation of temperature distribution and stress development in wire edm of tungsten carbide
by: Ali Imran, Awaludin, et al.
Published: (2022)

Optimization of EDM Small Hole Drilling Process Using Taguchi Approach
by: M. F. F., Ab Rashid, et al.
Published: (2016)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Single objective optimization of EDM machining on titanium workpiece using Taguchi method
by: Wan Mohd Ariff, Wan Azli
Published: (2012)

Surface Integrity Study In WEDM Of Tungsten Carbide
by: Mas Ayu, Hassan
Published: (2008)

Study Of The Surface Integrity Of The Machined Workpiece In The Wedm Of Tungsten Carbide
by: Mas Ayu, Hassan, et al.
Published: (2008)

Improvement of surface quality using silicon carbide powder added dielectric fluid during EDM
by: Khan, Ahsan Ali, et al.
Published: (2017)

Surface roughness studies in die-sink EDM of tungsten carbide using copper tungsten electrode
by: Konneh, Mohamed, et al.
Published: (2011)

Experiment On EDM Machining For Advance Engineering Material Using Taguchi Method
by: Mustafa, Mohammed Irfan
Published: (2005)

Determining Optimum EDM Parameters in Drilling a Small Hole by Taguchi Method
by: A. R., Yusoff, et al.
Published: (2009)

Investigation on the surface finish, MRR and the surface damage during the EDM of tungsten carbide
by: Khan, Ahsan Ali, et al.
Published: (2011)

Performance evaluation of wire electro-discharge machining on tungsten carbide
by: Hassan, Mas Ayu
Published: (2006)

Micromilling of tungsten carbide using focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Wire Electrical Discharge Machining of Tungsten Carbide
by: Mas Ayu, Hassan
Published: (2008)

Taguchi Method Approach for Recyling Chip Waste from Machining Aluminum (AA6061) Using Hot Press Forging Process
by: Mohamad Syahmi, Shahrom, et al.
Published: (2013)

Investigation of machining performance of the PVD coated tungsten carbide by sandblasting pre-treatment
by: Hariz Sufiyan, Mohamed Sunari
Published: (2012)

Thermal stability of laser-clad tool steel with fine tungsten carbide particle addition
by: Fazliana, Fauzun, et al.
Published: (2025)

Development of surface roughness models in end milling titanium alloy Ti-6Al-4V using uncoated tungsten carbide inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Achievement of ductile regime machining in high speed end milling of soda lime glass by using tungsten carbide tool insert
by: Amin, A. K. M. Nurul, et al.
Published: (2015)

Effect of tungsten carbide partial dissolution on the microstructure evolution of a laser clad surface
by: Fazliana, Fauzun, et al.
Published: (2020)

Evaluation Of Cutting Force in End Milling Process of Aluminum Alloy 6061-T6 Using Tungsten Carbide Inserts with MQL Method Utilizing Hybrid Nanofluid
by: Wahaizad, Safiei, et al.
Published: (2021)

Optimization of Chemical Pretreatment for Removing Cobalt on Tungsten Carbide Substrate Using Response Surface Methodology
by: A., Shah, et al.
Published: (2016)

Development, modeling, and experimental investigation of low frequency workpiece vibration-assisted micro-EDM of tungsten carbide
by: Jahan, M. P., et al.
Published: (2010)

Progressive tool wear in machining biomedical alloy using uncoated and titanium diboride coated tungsten carbide tools
by: Mohd Hafizu, Zakaria
Published: (2019)

Characterization of a wave soldering process using Taguchi method
by: Mohd. Rohani, Jafri, et al.
Published: (1999)

Modeling of Material Removal on Machining of Ti-6Al-4V through EDM using Copper Tungsten Electrode and Positive Polarity
by: M. M., Rahman, et al.
Published: (2010)

Wear Behaviour of Tungsten Carbide in End Milling Process of Aluminium Alloy 6061-T6 with Minimal Quantity of Tri-hybrid Nanofluids
by: W., Safiei, et al.
Published: (2023)

Influence of electrical parameters and optimization of EDM performance measures on Ti-6A1-4V using DOE/TAGUCHI method
by: Md Zain, Mohd Zahiruddin
Published: (2005)

Wear Mechanism of Coated and Uncoated Carbide Cutting Tool in Machining Process
by: J. A., Ghani, et al.
Published: (2016)

The performance of uncoated tungsten carbide insert in end milling titanium alloy Ti-6Al 4V through work piece preheating
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Viability of microwave hybrid sintering process for tungsten carbide cermets
by: Hammad Thauri, Shahdura
Published: (2016)

Optimization of Machining Parameters on Tool Wear Rate of Ti-6Al-4V through EDM using Copper Tungsten Electrode A Statistical Approach
by: M. M., Rahman, et al.
Published: (2011)

Performance of electrical discharge machining (EDM) with nickel added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Evaluation of corrosion and wear behaviour of nickel tungsten carbide electrodeposited with different tungsten carbide concentration and current density
by: Kamdi, Zakiah, et al.
Published: (2018)

Plasma transfer arc welding (PTAW) for depositing tungsten carbide-nickel cermet coating for corrosion
by: Kamdi, Zakiah
Published: (2020)

Sintering behaviour of cemented tungsten carbide and steel bilayer
by: Ojo-Kupoluyi, Oluwatosin Job, et al.
Published: (2017)