On the scaling of air launch vehicles

QR Code

On the scaling of air launch vehicles

The purpose of this paper is to introduce a set of scaling laws for the preliminary design of air launch vehicles. Scaling laws have been successfully used for the early stages of preliminary design of aerospace vehicles. A set of scaling laws for the preliminary design of air launch vehicle are...

Full description

Bibliographic Details
Main Authors:	Kafafy, Raed, Idres, Moumen, Aldheeb, M., Omar, H.
Format:	Proceeding Paper
Language:	English
Published:	2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/9068/ http://irep.iium.edu.my/9068/1/ICMAAE-11-163.pdf

Similar Items

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

Design of an autopilot for an autonomous unmanned aerial vehicle
by: Idres, Moumen, et al.
Published: (2011)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Modeling of compression systems
by: Idres, Moumen
Published: (2011)

Design of a medium scaled air vehicle flapping type / Abbas Siddiqui Mohammed
by: Abbas Siddiqui, Mohammed
Published: (2018)

Development of economical vehicle model for pedestrian-friendly front-end profile study
by: Kausalyah, Venkatason, et al.
Published: (2014)

Development and optimization of a vehicle front-end geometry model for improved pedestrian safety
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2014)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

Aeroelastic stability problem of air vehicle
by: Sulaeman, Erwin
Published: (2011)

Constrained model predictive control for proton exchange membrane fuel cell
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Fuel cell starvation control using model Predictive technique with laguerre and exponential weight functions
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

A Review of Compressed-air Hybrid Technology in Vehicle System
by: F., Wasbari, et al.
Published: (2017)

Development Of Hydraulic Launch Assist Testbench
by: Ramli, Muhammad Faiz
Published: (2019)

Surge and rotating stall
by: Idres, Moumen
Published: (2011)

Compressor models
by: Idres, Moumen
Published: (2011)

Cushion pressure control system for an intelligent air-cushion track vehicle
by: Hossain, Altab, et al.
Published: (2011)

Dynamic modeling of intelligent air-cushion tracked vehicle for swamp peat
by: Hossain, Altab, et al.
Published: (2011)

The stability of TiO2/POE nanolubricant for automotive air-conditioning system of hybrid electric vehicles
by: Mohd Hamisa, Abdul Hamid, et al.
Published: (2020)

Numerical simulation and validation of high-speed turbulent and chemically-reacting flows
by: Kamel, Mohammed, et al.
Published: (2015)