One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle

QR Code

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle

A new technology for micropropulsion which uses thermoelectric elements to control the wall temperature of microthrusters is under development at the International Islamic University Malaysia. In this new technology,solid state walls act as either flow heater or cooler based on the local flow Mach...

Full description

Bibliographic Details
Main Authors:	Mohammed Idres, Moumen, Hasan, Amar, Kafafy, Raed
Format:	Proceeding Paper
Language:	English
Published:	2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/9054/ http://irep.iium.edu.my/9054/4/ICMAAE-11-151.pdf

Similar Items

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Thermoelectrically controlled micronozzle - A novel application for thermoelements
by: Hameed, Amar Hasan, et al.
Published: (2012)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Improving the efficiency of micronozzle by heated sidewalls
by: Hameed, Amar Hasan, et al.
Published: (2011)

Modeling of non-uniform thermoelement devices subject to lateral heat convection
by: Kafafy, Raed, et al.
Published: (2011)

Generalized one-dimentional flow inside thermo-electrically controlled micronozzle
by: Hameed, Amar Hasan, et al.
Published: (2011)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Design of an autopilot for an autonomous unmanned aerial vehicle
by: Idres, Moumen, et al.
Published: (2011)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Two-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Unstructured finite volume for two-dimensional navier stokes equations.
by: Idres, Moumen
Published: (2011)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Investigation of heat transfer effect on polymerase chain reaction
by: Kafafy, Raed Ismail
Published: (2012)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Single-walled carbon nanotube modelling based on one-and two-dimensional Cosserat continua
by: Zhang, Yu
Published: (2011)

Experimental study of masonry wall exposed to blast loading
by: Ahmad, S, et al.
Published: (2013)

Capturing waste heat energy with charge-transfer organic thermoelectrics
by: Dimitrov, Vladimir, et al.
Published: (2018)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Investigations on physical characteristics of three-dimensional coil structure for MEMS magnetometer
by: Sulaiman, Nadzril, et al.
Published: (2013)

Thermoelectric properties of nanostructured tetrathiotetracene iodide crystals in a two-dimensional model
by: Sanduleac, Ionel, et al.
Published: (2014)

Low-cost and sustainable organic thermoelectrics based on low-dimensional molecular metals
by: Huewe, Florian, et al.
Published: (2017)

Modeling and analysis of flutter-based thin-film cantilever microgenerator
by: Abdul Hakim, Javid, et al.
Published: (2015)

Vehicle fuel consumption and emission modelling: an in-depth literature review
by: Faris, Waleed Fekry, et al.
Published: (2011)

Lateral side impact crash simulation of restrained 3 year old child
by: Shasthri, Sevaguru, et al.
Published: (2014)

Heat transfer enhancement of a modularised thermoelectric power generator for passenger vehicles
by: Li, Bo, et al.
Published: (2017)

Progress in one-dimensional nanostructures
by: Samykano, M.
Published: (2021)