Machinability study of ultrasonic assisted machining (UAM) of carbon fibre reinforced plastic (CFRP) with multifaceted tool

QR Code

Machinability study of ultrasonic assisted machining (UAM) of carbon fibre reinforced plastic (CFRP) with multifaceted tool

This paper discusses the conventional machining (CM) and ultrasonic assisted machining (UAM) of end milling carbon fibre reinforced plastic (CFRP). Tool condition, cutting forces and surface integrity of machined surface were evaluated. A commercially available tool with a diameter of 10mm and a ni...

Full description

Bibliographic Details
Main Authors:	Abd Halim, Nor Farah Huda, Ascroft, Helen, Barnes, Stuart
Format:	Proceeding Paper
Language:	English
Published:	Elsevier 2016
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/80871/ http://irep.iium.edu.my/80871/1/1-s2.0-S2212827116301962-main.pdf

Similar Items

Analysis of tool wear, cutting force, surface roughness and machining temperature during finishing operation of ultrasonic assisted milling (UAM) of carbon fibre reinforced plastic (CFRP)
by: Abd Halim, Nor Farah Huda, et al.
Published: (2017)

Ultrasonic assisted machining
by: Ascroft, Helen, et al.
Published: (2016)

The effect of varying cutting speeds on tool wear during conventional and Ultrasonic Assisted Drilling (UAD) of Carbon Fibre Composite (CFC) and titanium alloy stacks
by: Dahnel, Aishah Najiah, et al.
Published: (2016)

Analysis of tool wear and hole quality during Ultrasonic Assisted Drilling (UAD) of Carbon Fibre Composite (CFC)/titanium alloy (Ti6Al4V) stacks
by: Dahnel, Aishah Najiah, et al.
Published: (2015)

The effect of milling parameters on laminated carbon fibre reinforced plastic (CFRP)
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2012)

Compressive Properties of Carbon Fibre Reinforced Plastic (CFRP) at Low Strain Rate
by: Ahmad, Roslan, et al.
Published: (2001)

Performance evaluation of drilling tools during machining plain Carbon Fiber Reinforced Polymer (CFRP)
by: Konneh, Mohamed, et al.
Published: (2015)

Fabrication of the carbon ﬁber reinforced plastic (CFRP) cone tube through the laboratory-scale 3-axis winding machine
by: Ma, Quanjin, et al.
Published: (2021)

Fabrication of the carbon fiber reinforced plastic (CFRP) cone tube through the laboratory-scale 3-axis winding machine
by: Ma, Quanjin, et al.
Published: (2020)

2016_Down Milling Trimming Process Optimization for Carbon Fibre Reinforced Plastic (Cfrp)

Study on tool wear during milling CFRP under dry and chilled air machining
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

A metrological inspection method using micro-CT for the analysis of drilled holes in CFRP and titanium stacks
by: Kourra, Nadia, et al.
Published: (2017)

Optimization of milling carbon fibre reinforced plastic under chilled air machining
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Development of an active fixture for ultrasonically assisted micro electro-discharge machining
by: Mollik, Md Shohag, et al.
Published: (2019)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari, Azmir, et al.

Learning experience of machining carbon Fibre CFRP AL2024 using Design of Experiment (DoE) approach

Learning experience of machining carbon fibre CFRP AL2024 using Design of Experiment (DoE) approach

The Effect on the Application of Coolant and Ultrasonic Vibration Assisted Micro Milling on Machining Performance
by: Rasidi, Ibrahim, et al.
Published: (2014)

A review on feasibility study of ultrasonic assisted machining on aircraft component manufacturing

Study of cutting forces and surface roughness in milling of Carbon Fibre Composite (CFC) with conventional and pressurized CO2 cutting fluids
by: Dahnel, Aishah Najiah, et al.
Published: (2015)

Developments in Machining of Stacked Materials Made of CFRP and Titanium/Aluminium Alloys
by: Pramanik, Alokesh, et al.
Published: (2014)

Heat-assisted machining
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Machinability aspects in heat assisted machining of hardened steel AISI H13 using coated carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Multifaceted protocol in biotechnology
Published: (2018)

Tool wear during milling laminated carbon fibre reinforced plastic
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2015)

The optimization study on the tool wear of carbide cutting tool during milling Carbon Fibre Reinforced (CFRP) using Response Surface Methodology (RSM)
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2018)

A review on the rotary ultrasonic machining of advanced ceramics
by: Khoo, C. Y., et al.
Published: (2008)

Influence of machining parameters on temperature when drilling carbon fiber reinforced polymer (CFRP) using coated diamond drills
by: Konneh, Mohamed, et al.
Published: (2015)

Machining and Tool Wear Mechanisms during Machining Titanium Alloys
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Cryogenic-assisted high speed machining
by: Sue-Rynley, Anak Emley
Published: (2008)

Ultrasonic measurements and machine learning methods to monitor industrial processes
by: Bowler, Alexander
Published: (2023)

Joining of carbon fibre reinforced polymer (CFRP) composites and aluminium alloys – A review
by: Pramanik, A., et al.
Published: (2017)

COMMUNITY ENGAGEMENT: A multifaceted process
by: Nematollahi, Shohreh
Published: (2017)

Multifaceted link between cancer and inflammation
by: Sethi, G., et al.
Published: (2012)

A multifaceted analysis of tourism satisfaction
by: Neal, J., et al.
Published: (2008)

Cinnamon: A Multifaceted Medicinal Plant
by: Pasupuleti, Visweswara Rao, et al.
Published: (2014)

Performance of diamond tool in machining titanium
by: Ahmad Nazmi, Mohd Rose
Published: (2010)

Effect of dry machining on tool wear
by: Madihah, Zubir
Published: (2012)

Tool wear and surface roughness on milling carbon fibre reinforced plastic using chilled air
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2012)