Capabilities of cermets tools for high speed machining of austenitic stainless steel

QR Code

Capabilities of cermets tools for high speed machining of austenitic stainless steel

Cermets tools have very high hot hardness together with a low coefficient of friction, which facilitates machining at high speeds. In the present work cermet tools coated with titanium nitride were used to turn austenitic stainless steel at speeds between 300 and 700 m min-1. Feed rates were varied...

Full description

Bibliographic Details
Main Authors:	Khan, Ahsan Ali, Salama Hajjaj, Sami
Format:	Article
Language:	English
Published:	Asian Network for Scientific Information 2006
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/7858/ http://irep.iium.edu.my/7858/1/779-784.pdf

Similar Items

An investigation on low-temperature thermochemical treatments of austenitic stainless steel in fluidized bed furnace
by: Haruman, Esa, et al.
Published: (2012)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

A feasibility study on low temperature thermochemical treatments of Austenitic Stainless Steel in Fluidized Bed Furnace
by: Haruman, Esa, et al.
Published: (2011)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Optimization of process parameters on EDM milling of stainless steel AISI 304
by: A.K.M, Asif Iqbal, et al.
Published: (2011)

A new approach of applying cryogenic coolant in turning AISI 304 stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

A Method and an Apparatus for Machining a Tool Steel
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Implementation of magnetic damping to reduce chatter amplitude and tool wear during turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Experimental investigation of chip tool contact process and determination of optimum cutting speed for steel of any composition
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Development of mathematical model for chip serration frequency in turning of stainless steel 304 using RSM
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Criteria for determining machinability and techniques of improving machinability of steel and alloys
by: Amin, A. K. M. Nurul
Published: (1993)

Tool wear and surface finish investigation in high speed turning using cermet insert by applying negative rake angles
by: Adesta, Erry Yulian Triblas, et al.
Published: (2009)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

The effects of process variables on the hardness of nitrided 3% chromium steel
by: Mridha, Shahjahan, et al.
Published: (2008)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Dissimilar materials laser welding characteristics of stainless steel and titanium alloy
by: Mohid, Zazuli, et al.
Published: (2014)

Improving tool life using cryogenic cooling
by: Khan, Ahsan Ali, et al.
Published: (2008)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)