Surface modification using Electric Discharge Machining (EDM) with powder addition

QR Code

Surface modification using Electric Discharge Machining (EDM) with powder addition

Powder mixed electrical discharge machining (PMEDM) is one of the recent innovations for the enhancement of the capabilities of EDM process. In this study, the effects of powder addition on the surface modification of mild steel were investigated. Copper tungsten electrode was used in the machini...

Full description

Bibliographic Details
Main Authors:	Khan, Ahsan Ali, Mohammed , Baba Ndaliman, Mohd Zain, Zakaria, Jamaludin, Mohammad F., Patthi, Umar
Format:	Article
Language:	English
Published:	Trans Tech Publications Ltd., Switzerland 2011
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/7043/ http://irep.iium.edu.my/7043/1/Published_Singapore.pdf

Similar Items

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Surface modification by EDM using Co-Cr sintered powder metallurgy electrode
by: Khan, Ahsan Ali, et al.
Published: (2012)

Surface modification by EDM using CO-CR sintered powder metallurgy electrod
by: Khan, Ahsan Ali, et al.
Published: (2012)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrodes for EDM
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2011)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Developments in EDM process variables
by: Khan, Ahsan Ali, et al.
Published: (2011)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Performance of PM compacted Cu-TaC electrodes during EDM
by: Mohammed, Baba Ndaliman, et al.
Published: (2011)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Investigation of the influence of the properties of the work and tool materials on performance level of Electrical Discharge Machining (EDM) process
by: A.K.M., N. Amin, et al.
Published: (1997)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Determination of influential factors on EDMed surface properties using Plackett-Burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Determination of influential factors on edmed surface properties using plackett-burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Influence of thermal conductivity cf electrodes on EDM process parameters
by: Khan, Ahsan Ali, et al.
Published: (2012)

Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
by: Khan, Ahsan Ali, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)