Study on tool wear and tool life during milling JFRP using uncoated carbide cutting tool

QR Code

Study on tool wear and tool life during milling JFRP using uncoated carbide cutting tool

Jute fiber-reinforcement polymer (JFRP) composite is a cheap material that is broadly used in automotive, marine, air- crafts, domestic upholstery applications because of its various high quality properties. During machining, a few of problems arise due to the Jute fiber in JFRP. Abrasive nature of...

Full description

Bibliographic Details
Main Authors:	Rashid, Mohammed Abdur N., Khan, Sher Afghan, Muhamad Khairussaleh, Nor Khairusshima, Sarifuddin, Norshahida
Format:	Article
Language:	English English
Published:	Asian Research Publishing Network (ARPN). 2018
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/64195/ http://irep.iium.edu.my/64195/13/64195%20Study%20on%20tool%20wear%20and%20tool%20life%20during.pdf http://irep.iium.edu.my/64195/14/64195%20Study%20on%20tool%20wear%20and%20tool%20life%20during%20SCOPUS.pdf

Similar Items

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Effectiveness of uncoated WC-Co and PCD inserts in end milling of aluminum silicon carbide (AlSiC)
by: M. K., Nor Khairusshima, et al.
Published: (2007)

A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
by: Khan, Ahsan Ali, et al.
Published: (2011)

Experimental determination of optimum cutting conditions in turning low alloyed steel with cemented carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Investigation of the influence of chatter on tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Influence of work material, cutting conditions and rigidity of tool holders on machine tool chatter
by: Amin, A. K. M. Nurul
Published: (1992)

Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
by: Iqbal, Mohammad, et al.
Published: (2015)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Surface roughness model for high speed end milling of soda lime glass using carbide coated tools with compressed air blowing
by: Mahmud, M. A., et al.
Published: (2012)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Modeling and optimization of surface roughness and vibration amplitude in heat assisted end milling of SKD 11 tool steel using ball nose tool
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
by: A.K.M., Nurul Amin, et al.
Published: (2007)

Minimum Quantity Lubrication (MQL) and its effect on tool wear during miniature drilling: an experimental study
by: Mohamad, Norsalawani, et al.
Published: (2016)

Improved tool life in end milling ti-6al-4v through workpiece preheating
by: Ginta , Turnad L., et al.
Published: (2009)

Improving tool life using cryogenic cooling
by: Khan, Ahsan Ali, et al.
Published: (2008)

Implementation of magnetic damping to reduce chatter amplitude and tool wear during turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Experimental investigation of chip tool contact process and determination of optimum cutting speed for steel of any composition
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
by: Turnad L., Ginta, et al.
Published: (2008)

Influence of sintering temperature on density, hardness, shrinkage and microstructure of alumina-zirconia cutting tool
by: A. A., Anis, et al.
Published: (2021)

Study on wear mechanism of solid carbide cutting tool in milling CFRP
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2016)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Statistical approach to modeling & optimization of surface roughness in high speed end milling of silicon with diamond coated tools
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2
by: Amin, A. K. M. Nurul, et al.
Published: (2008)

A Method and an Apparatus for Machining a Tool Steel
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Surface roughness optimization in end milling of stainless steel AISI 304 with uncoated WC-Co insert under magnetic field
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Influence of the characteristics of Machine-Tool-Fixture-Work (MTFW) system on chatter
by: Amin, A. K. M. Nurul
Published: (1985)

Wear Mechanism of Coated and Uncoated Carbide Cutting Tool in Machining Process
by: J. A., Ghani, et al.
Published: (2016)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Investigation on tool wear rate for modified and unmodified aluminium-silicon casting alloy
by: Haque, Md. Mohafizul, et al.
Published: (2009)

Investigation of chatter arising in Machine Tool-Fixture Work (MTFW) system during turning
by: Amin, A. K. M. Nurul, et al.
Published: (1994)

Influence of the instability of chip formation and preheating of work on tool life in maching high temperature resistant steel and titanium alloys
by: Amin, A. K. M. Nurul, et al.
Published: (1986)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)