The true inventor of some early mechanical engineering devices and mechanisms

QR Code

The true inventor of some early mechanical engineering devices and mechanisms

For centuries the inventions of automated crankshaft, camshaft, reciprocating double-action piston suction hydraulic pump with suction pipes, overshot curvaceous water turbines, andcrank-connecting rod mechanism have been credited to Leonardo da Vinci (1452 – 1519) and Lester Allan Pelton (1829 – 19...

Full description

Bibliographic Details
Main Authors:	Faris, Waleed Fekry, Elmoselhy, Salah
Format:	Article
Language:	English
Published:	IIUM Press, International Islamic University Malaysia 2017
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/63094/ http://irep.iium.edu.my/63094/1/63094_THE%20TRUE%20INVENTOR%20OF%20SOME%20EARLY.pdf

Similar Items

Introduction to machine element design for engineers
by: Faris, Waleed Fekry
Published: (2011)

Validated analytical modeling of diesel engine regulated exhaust CO emission rate
by: Faris, Waleed Fekry, et al.
Published: (2016)

Active engine mounting control algorithm using neural network
by: Darsivan, Fadly Jashi, et al.
Published: (2009)

Thermal design of mechanical devices using expert system
by: Mohiuddin, A. K. M.
Published: (2011)

Mechanical behavior of an electrostatically actuated micropump
by: Faris, Waleed Fekry, et al.
Published: (2002)

Contact-impact problems using a quasi-linear finite element appraoch
by: Faris, Waleed Fekry
Published: (2012)

Experimentally validated analytical modeling of diesel engine power and in-cylinder gas speed dynamics
by: Elmoselhy, Salah A M, et al.
Published: (2016)

Active engine mounting controller design using linear quadratic regulator and proportional integral derivative
by: Mahil, M. mahil, et al.
Published: (2011)

Fundamentals of fluid mechanics
by: Faris, Waleed Fekry, et al.
Published: (2009)

Validated analytical modelling of supercharging centrifugal compressors with vaneless diffusers for H2-biodiesel dual-fuel engines with cooled EGR
by: Elmoselhy, Salah A.M., et al.
Published: (2017)

Dynamic characterisation of elastomeric engine mounts of different geometry used in automotive industry: simulation approach
by: Faris, Waleed Fekry, et al.
Published: (2010)

A comparison between two solution approaches for diaphragm-based capacitive pressure microsensor
by: Faris, Waleed Fekry, et al.
Published: (2004)

Ergonomic Design of a Mechanical Device for Increasing the Rate of Union in Open Fractures of the Tibia
by: Long,, Pan Kok, et al.
Published: (2000)

E-beam sterilizable thermoplastics elastomers for healthcare devices: Mechanical, morphology, and in vivo studies
by: Balaji, Anand B., et al.
Published: (2018)

A first course in control systems
by: Faris, Waleed Fekry, et al.
Published: (2009)

Modelling manufacturing process using a modified IDEF0 framework a case study of a car door manufacturing plant
by: Al-Turki , Abdullah, et al.
Published: (2010)

EMM 101 ENGINEERING MECHANICS (DEC 2015)
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal

EMM 101 – Engineering Mechanics (Mekanik Kejuruteraan)
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2024)

Design of two stroke SI linear engine with spring mechanism
by: Mohd Faizal, Mohd Pauzi
Published: (2008)

Effect on swept volume on cooling using pumping mechanism based device / Noor Aishah Rabion
by: Rabion, Noor Aishah
Published: (2016)

EEM 353 MECHANICAL ENGINEERING DESIGN (JAN 2016)
by: PPKEE, Pusat Pengajian Kejuruteraan Elektrik & Elektronik
Published: (2016)

EMM101-3 - ENGINEERING MECHANICS NOVEMBER 2008
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2008)

Assessment of The Mechanical Engineering Programs by Exit Surveys at Universiti Malaysia Pahang
by: M. S. M., Sani, et al.
Published: (2008)

Simulation of disturbance rejection control of half-car active suspension system using ADRC with decoupling transformation
by: Hasbullah, Faried, et al.
Published: (2018)

Micropump modeling: current status and challenges
by: Faris, Waleed Fekry, et al.
Published: (2012)

EMM 1013 – ENGINEERING MECHANICS NOV 2010.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2010)

Active engine mounting controller using extended minimal resource allocating networks
by: Darsivan, Fadly Jashi, et al.
Published: (2008)

Design of a mechanism to mix biogas with air in compression internal combustion engine
by: Ahmad Hazury, Hamid
Published: (2010)

EMM 101(3) - MECHANICAL ENGINEERING OCT-NOV 07.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2007)

Measurement And Management Of Energy Usage In School Of Mechanical Engineering USM
by: Arbain, Azizi
Published: (2018)

Device inventors from UPM enjoy 'shocking' win
by: Thevadass, Logeiswary
Published: (2016)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Wireless technology applied in 3-axis filament winding machine control system using MIT app inventor
by: Quanjin, Ma, et al.
Published: (2019)

EMM 101/3 - ENGINEERING MECHANICS JUN 09.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2009)

EMM 101-3 - ENGINEERING MECHANICS NOV 10.
by: ppkm, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2010)

EMM101 – Engineering Mechanics Duration : 3 hours
by: Mekanik, Pusat Pengajian Kejuruteraan
Published: (2022)

Contact-impact problems using a quasi-linear finite element approach
by: Faris, Waleed Fekry
Published: (2012)

Simulation of the ignition mechanisms of low and high octane number blended fuels in HCCI engine
by: Muthanna, Jamil, et al.
Published: (2020)

Implementation of outcome based education in the faculty of mechanical engineering, universiti malaysia pahang : An experience
by: Mohd Ruzaimi, Mat Rejab, et al.
Published: (2008)

Simulation of the ignition mechanisms of low and high octane number blended fuels in HCCI engine
by: Munthanna, Jamil, et al.
Published: (2020)