Evaluation of fatigue damage in adhesive bonding:
Part 1: Bulk adhesive

QR Code

Evaluation of fatigue damage in adhesive bonding: Part 1: Bulk adhesive

The measurement of fatigue damage in adhesive bonding has been investigated. Bulk adhesive was used in this study for two reasons: the stress distribution of adhesives in bulk is simpler to investigate than adhesives in joints; and the specimen dimensions met fatigue test standards. Bulk adhesive...

Full description

Bibliographic Details
Main Authors:	Wahab, Magd Abdel, Hilmy, Irfan, Ashcroft, Ian Anthony, Crocombe, Andrew David
Format:	Article
Language:	English
Published:	Taylor and Francis 2010
Subjects:	T Technology (General) TJ170 Mechanics applied to machinery. Dynamics
Online Access:	http://irep.iium.edu.my/62706/ http://irep.iium.edu.my/62706/1/10.1163%40016942409x12508517390798.pdf

Similar Items

Finite element modelling of damage fracture and fretting fatigue
by: Wahab, M. Abdel, et al.
Published: (2012)

Monitoring of fatigue damage using ultrasonics and finite element analysis
by: Hrairi, Meftah, et al.
Published: (2012)

On the use of low and high cycle fatigue damage models
by: Abdel Wahab, Magd, et al.
Published: (2013)

The damage of unconfined granite edge due to the impact of varying stiffness projectiles
by: Shah, Qasim Hussain, et al.
Published: (2013)

Implementation of lean manufacturing to blend with good manufacturing practice at Minda Tulus Industries Sdn. Bhd. for improved performance
by: Nasry, Nasrul Ashraf, et al.
Published: (2017)

Development of design structure matrix of product architecture case study: multi purpose CNC router
by: Hilmy, Irfan, et al.
Published: (2014)

The thermo-mechanical degradation of ethylene vinyl acetate used as a solar panel adhesive and encapsulant
by: Badiee, A., et al.
Published: (2016)

Approximate analytical method for damage detection in free–free beam by measurement of axial vibrations
by: FB, Sayyad, et al.
Published: (2013)

Experimental investigation on frequency shifting of imperfect adhesively bonded pipe joints
by: Haiyam, F. N., et al.
Published: (2018)

The application of adhesive bonding for different types of material for car body parts
by: Muhammad Shahir, Nazir
Published: (2013)

Numerical investigation of flow boiling in double-layer microchannel heat sink
by: Ahmed, Shugata, et al.
Published: (2014)

Performance and cost analysis of diesel engine with different mixing ratio of raw vegetable oil and diesel fuel
by: Uddin, Md. Nasir, et al.
Published: (2016)

Modal analysis of car panels using finite element analysis
by: Hanouf, Zahir
Published: (2011)

Biodiesel production process optimization from spirulina maxima microalgae and performance investigation in a diesel engine
by: Rahman, Md Atiqur, et al.
Published: (2017)

Image-based feature extraction technique for inclined crack quantification using pulsed eddy current
by: Nafiah, Faris, et al.
Published: (2019)

Development of vibration suppression devices from smart fluids
by: Rashid, Muhammad Mahbubur, et al.
Published: (2011)

Development of fuzzy logic controller for magnetorheological rotary brake system
by: Rashid, Muhammad Mahbubur, et al.
Published: (2009)

Dynamics and control policies analysis of semi-active suspension systems using a full-car model
by: Ihsan, Sany Izan, et al.
Published: (2007)

An evaluation of LQR and fuzzy logic controllers for active suspension using half car model
by: Hasbullah, Faried, et al.
Published: (2010)

A study of noise transmission through cylindrical shell using modal truncation approach
by: El-Hafidi, Ali, et al.
Published: (2011)

Dynamic characterisation of elastomeric engine mounts of different geometry used in automotive industry: simulation approach
by: Faris, Waleed Fekry, et al.
Published: (2010)

Active engine mounting controller using extended minimal resource allocating networks
by: Darsivan, Fadly Jashi, et al.
Published: (2008)

Investigation into noise problems in vehicle structure using vibro-acoustic approach
by: Hanouf, Zahir Ahmad, et al.
Published: (2009)

Evaluation of friction welded bi-material joint strength subjected to impact loads
by: Shah, Qasim Hussain, et al.
Published: (2011)

Aerodynamic derivatives identification for ground vehicles in crosswind using neural network and PCA
by: Ramli, Nabilah, et al.
Published: (2010)

Load carrying capability of liquid filled cylindrical shell structures under axial compression
by: Hussain Shah, Qasim, et al.
Published: (2011)

Experimental and numerical study on the orthogonal and oblique impact on water filled pipes
by: Hussain Shah, Qasim
Published: (2011)

Effect of tapered angle of a conical nose indenter on the energy absorbing variation of a copper pipe subjected to axial crushing
by: Shah, Qasim Hussain, et al.
Published: (2012)

A comparison of energy absorbing capabilities of paper and steel structures subjected to progressive failure under free falling objects
by: Shah, Qasim Hussain, et al.
Published: (2007)

LS-DYNA for beginners: an insight into Ls-Prepost and Ls-Dyna
by: Hussain Shah, Qasim, et al.
Published: (2012)

Analysis of thermal stress intensity factors for edge cracked bimaterial system
by: Hrairi, Meftah, et al.
Published: (2012)

Development of palmprint based biometric system
by: Rotinwa-Akinbile, M. A., et al.
Published: (2011)

Kernel PCA – an introduction
by: Baali, Hamza, et al.
Published: (2011)

System modelling of a twin rotor system: time and frequency domain analysis
by: Toha, Siti Fauziah, et al.
Published: (2011)

Review of Malaysian traffic summon and payment system
by: Aibinu, Abiodun Musa, et al.
Published: (2011)

Hot Water Rocket System (HWRS) - preliminary design and prototype development of a pressurized how water casing (PHWC)
by: Kashif, Syed Muhammad
Published: (2012)

Post impact fatigue of fibre metal laminate (FML) / Abdul Adzim Abdul Mubin.
by: Abdul Mubin, Abdul Adzim
Published: (2009)

Adhesive bonding of thermoplastic polyurethane with metallic wire
by: Abdullahi, Tijjani, et al.
Published: (2018)

Influence of internal fill pattern, polishing time and Z-Axis orientation on the tensile strength of the 3D printed part
by: Seprianto, Dicky, et al.
Published: (2019)

Post impact fatigue of kenaf powder, PP, MAPP laminated with kevlar hybrid composites / Siti Norain Manan.
by: Manan, Siti Norain
Published: (2009)