Transient flow in a compressor blade row for a periodic
vibration motion

QR Code

Transient flow in a compressor blade row for a periodic vibration motion

The goal of this work is to conduct a transient compressor blade row flow simulation as part of blade flutter modeling. An integral step of blade flutter modeling is the calculation of the aerodynamic damping factor as a function of the possible vibration mode shapes. Using Fourier method, the nu...

Full description

Bibliographic Details
Main Authors:	Idres, Moumen, Labanie, Mohamed, Okasha, Mohamed Elsayed Aly Abd Elaziz
Format:	Proceeding Paper
Language:	English English
Published:	IOP Publishing 2018
Subjects:	TA Engineering (General). Civil engineering (General) TA349 Mechanics of engineering. Applied mechanics
Online Access:	http://irep.iium.edu.my/61996/ http://irep.iium.edu.my/61996/13/61996_Transient%20flow%20in%20a%20compressor%20blade%20row_scopus.pdf http://irep.iium.edu.my/61996/19/61996_Transient%20flow%20in%20a%20compressor%20blade%20row%20for%20a%20periodic.pdf

Similar Items

Relative motion and autonomous rendezvous in Keplerian elliptic orbits
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2010)

Relative motion guidance, navigation and control for autonomous orbital rendezvous
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2011)

Relative motion guidance, navigation and control for autonomous spacecraft rendezvous
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2011)

Relative motion guidance, navigation and control for autonomous orbital rendezvous
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2014)

Switching algorithm to avoid attitude representation singularity
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2009)

Switching principles to circumvent Euler angle singularity
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2010)

Guidance, navigation and control for satellite proximity operations using Tschauner-Hempel equations
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2011)

Compressor models
by: Idres, Moumen
Published: (2011)

Assessment of earth remote sensing microsatellite power subsystem sapability during detumbling and nominal modes
by: Zahran, Mohamed, et al.
Published: (2006)

Autonomous multi satellites assembly in keplerian orbits
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2013)

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

A numerical study of transient natural convection of water near its density extremum
by: Othman, Safiah
Published: (2005)

Trajectory tracking of quaternion based quadrotor using model predictive control
by: Islam, Maidul, et al.
Published: (2018)

Investigation of Malaysian low earth orbits for remote sensing applications
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2017)

The effects of absorber attachment location on vibration response of simply supported plate
by: Mohamed Salleh, Muhammad, et al.
Published: (2016)

Finite element modelling of fixed-fixed end plate attached with vibration absorber
by: Mohamed Salleh, Muhammad, et al.
Published: (2016)

Dynamic effects of piezoelectric patch actuators on vibrational response of non-deterministic structures: modelling and simulations
by: Wahid, Azni Nabela, et al.
Published: (2015)

Compensated inverse pid controller for active vibration control with piezoelectric patches: modeling, simulation and implementation
by: Abdul Muthalif, Asan Gani, et al.
Published: (2006)

Thermoelastic slutions for flexure of anisotropic cylindrical shells
by: Mohamed Ali, Jaafar Syed
Published: (2015)

FRGS15-165-0406: MATHEMATICAL ANALYSIS TO ESTIMATE OPTIMAL SHUNT IMPEDANCE FOR PIEZOELECTRIC TRANSDUCER TO MAXIMIZE VIBRATION ENERGY DISSIPATION IN NON-DETERMINISTIC SUB-SYSTEMS
by: Muthalif, Asan G. A.
Published: (2018)

A numerical study of transient natural convection of water near its density extremum
by: Othman, Safiah
Published: (2005)

Development of educational software for stress analysis of an aircraft wing
by: Mohamed Ali, Jaafar Syed, et al.
Published: (2012)

Hygrothermoelastic analysis of anisotropic cylindrical shells
by: Alsubari, Saleh, et al.
Published: (2015)

A higher order theory for bending of cross ply laminated cylindrical shell under hygrothermal loads
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2015)

Morphologies and mechanical properties of polylactic acid / polypropylene carbonate (PLA/PPC) blends by solvent casting method
by: Mohamed Haneef, Intan Najwa Humaira, et al.
Published: (2018)

Integrated protocol for ground and structures condition assessments using ambient vibration
by: Kamarudin, Ahmad Fahmy
Published: (2020)

Vibration simulation of a simply-supported beam with attached multiple absorbers
by: Idris, Mohd Azli
Published: (2015)

New design of tuned vibration absorber for wide frequency range application
by: Ghazali, Mohd Hafiz
Published: (2015)

Dynamics and control of quadcopter using linear model predictive control approach
by: Islam, M, et al.
Published: (2017)

Guidance solutions for multiple vehicle assembly
by: Okasha, Mohamed Elsayed Aly Abd Elaziz
Published: (2014)

Fatigue fracture process of lead-free solder joints in BGA package
by: Tamin, M.N., et al.
Published: (2012)

Damage mechanics model for solder/intermetallics interface fracture process in solder joints
by: Shaffiar, Norhashimah, et al.
Published: (2011)

Finite element modeling of clinching process for joining dissimilar materials
by: Eshteyah, Mohanna, et al.
Published: (2015)

Damage progression in BGA solder joints during board-level drop test
by: Yamin, A.F.M., et al.
Published: (2011)

Progressive damage in Sn-4Ag-0.5Cu solder joints during flexural fatigue of a BGA package
by: Shaffiar, Norhashimah, et al.
Published: (2010)

Continuum damage evolution in pb-free solder joint under shear fatigue loadings
by: Shaffiar, Norhashimah, et al.
Published: (2010)

3D modeling of austenite based on real microstructure
by: Prawoto, Yunan, et al.
Published: (2012)

Solder joint reliability assessment: finite element simulation methodology
by: Tamin, M.N., et al.
Published: (2014)

Quasi-two-dimensional MHD duct flow around a 180-degree sharp bend in a strong magnetic field
by: Mohammed Sapardi, Mohd Azan, et al.
Published: (2014)