Analysis of WEDM process parameters on surface roughness and kerf using Taguchi method

QR Code

Analysis of WEDM process parameters on surface roughness and kerf using Taguchi method

In obtaining the best quality of engineering parts, the quality of machined surface plays an essential role. The fatigue strength, wear resistance, and corrosion of workpiece are some of the aspects of the qualities that can be improved. This paper investigates the effect of wire electrical discharg...

Full description

Bibliographic Details
Main Authors:	Banu, Asfana, Bakar, Mazilah Abu, Ali, Mohammad Yeakub, Adesta, Erry Yulian Triblas
Format:	Article
Language:	English
Published:	Deer Hill Publications 2017
Subjects:	T Technology (General) T55.4 Industrial engineering.Management engineering. TS Manufactures TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/60691/ http://irep.iium.edu.my/60691/1/36-316-3-PB.pdf

Similar Items

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Cutting temperature and surface roughness optimization in CNC end milling using multi objective genetic algorithm
by: Al Hazza, Muataz, et al.
Published: (2012)

Influence of energy parameters of micro WEDM on kerf
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

New approach in cost structuring of high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Flank Wear Modeling in High Speed Hard Turning by using artificial Neural Network and Regression Analysis
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

A study of parameters relationship to backcutting phenomena during high speed end milling of AISI H13
by: Adesta, Erry Yulian Triblas, et al.
Published: (2010)

A feasibility study on low temperature thermochemical treatments of Austenitic Stainless Steel in Fluidized Bed Furnace
by: Haruman, Esa, et al.
Published: (2011)

An investigation on low-temperature thermochemical treatments of austenitic stainless steel in fluidized bed furnace
by: Haruman, Esa, et al.
Published: (2012)

Modeling the effect of CNT concentration in dielectric fluid on EDM performance using neural network
by: Khan, Ahsan Ali, et al.
Published: (2016)

Energy cost modeling for high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Micro wire electro discharge grinding: optimization of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Material removal rate of zirconia in electro discharge micromachining
by: Asfana, Banu, et al.
Published: (2015)

Dimensional accuracy of micro-electro discharge milling
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

Investigation of vibration in micromilling with MQL: S/N ratio analysis
by: Hussin, Muhammad Shaffiq, et al.
Published: (2020)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Investigation of surface roughness and material removal rate for high speed micro end milling on PMMA
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2015)

Investigation of surface roughness in micro-EDM of nonconductive ZrO2 ceramic with powder mixed dielectric fluid
by: Sabur, Abdus, et al.
Published: (2015)

Significant parameters for the surface roughness in incremental forming process
by: Echrif, Salah B. M., et al.
Published: (2014)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Precision control of kerf in metal cutting using dry micro WEDM: issues and challenges
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Modeling and analysis of MRR, EWR and surface roughness in EDM milling through response surface methodology
by: Asif Iqbal, A.K.M., et al.
Published: (2010)

Effect of cutting parameters on surface roughness in end milling of AlSi/AlN metal matrix composite
by: Tomadi, Siti Haryani, et al.
Published: (2017)