Numerical investigation of springback in mechanical clinching process

QR Code

Numerical investigation of springback in mechanical clinching process

In this work, a numerical investigation was conducted to study the springback phenomena in the mechanical clinching process. The springback values were calculated using finite element simulations and it was found that these values depend strongly on the strength of the materials. A Taguchi optimizat...

Full description

Bibliographic Details
Main Authors:	Eshteyah, Mohanna Moh'd Saleem, Hrairi, Meftah, Shaik Dawood, Mohd. Sultan Ibrahim
Format:	Article
Language:	English
Published:	2017
Subjects:	TA349 Mechanics of engineering. Applied mechanics TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/60164/ http://irep.iium.edu.my/60164/1/31-321-4-PB.pdf

Similar Items

Multi-objective optimization of clinching joints quality using Grey-based Taguchi method
by: Eshteyah, Mohanna, et al.
Published: (2016)

Clinching process for joining dissimilar materials: state of the art
by: Eshteyah, Mohanna, et al.
Published: (2016)

Finite element modeling of clinching process for joining dissimilar materials
by: Eshteyah, Mohanna, et al.
Published: (2015)

Finite element modeling of clinching process for joining dissimilar materials
by: Eshteyah, Mohanna, et al.
Published: (2015)

Finite element simulation of electro-mechanical impedance technique
by: Tahmasebpour, Kamyar, et al.
Published: (2015)

Derivation of stress intensity factor for a cracked plate with an integrated piezoelectric actuator
by: Abuzaid, Ahmed, et al.
Published: (2014)

An investigation of temperature effect on incremental forming
by: Echrif, Salah B. M., et al.
Published: (2013)

Finite element investigation of some aspects affecting the depth and wall thickness of a part formed by single point incremental forming process
by: Echrif, Salah B. M., et al.
Published: (2012)

Significant parameters for the surface roughness in incremental forming process
by: Echrif, Salah B. M., et al.
Published: (2014)

Mechanical performance of montmorillonite dispersed jute reinforced composite
by: Muhammad Hasibul , Hasan, et al.
Published: (2015)

Investigation of the mechanism of chatter formation during metal cutting process
by: Amin, A. K. M. Nurul
Published: (1983)

Enhancing mechanical and structural properties of TiC inserts using microwave energy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Role of mechanical alloying parameters on powders distribution of Al/Cu alloy and Al/Cu composite
by: Jamal, N. A., et al.
Published: (2014)

Numerical study on failure process of aluminium plate subjected to normal impact by hemispherical projectiles
by: Ibrahim, Mohd Norihan, et al.
Published: (2014)

Stress analysis of plate with opposite semicircular notches and adhesively bonded piezoelectric actuators
by: Abuzaid, Ahmed, et al.
Published: (2020)

Optimization of composite patch repair for center-cracked rectangular plate using design of experiments method
by: Aabid, Abdul, et al.
Published: (2020)

Effect of triggering angles on the crushing mechanisms of hybrid woven kenaf/aluminum hollow cylinders
by: Ismail, Al Emran, et al.
Published: (2017)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

Edge Crack, Bimaterial Systems
by: Hrairi, Meftah, et al.
Published: (2014)

Edge crack, composite materials
by: Rizk, Abd El-Fattah, et al.
Published: (2014)

Edge crack, isotropic material
by: Rizk, Abd El-Fattah, et al.
Published: (2014)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

A study on material removal rate during EDM with tantalum carbide-copper compacted electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of EDM of mild steel with Ta-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of current, spark on-time and off-time on electrode wear during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

A comparative study on work surface hardness EDMed by Ta-C powder compacted and copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Eco-friendly machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2012)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Role of current, voltage and spark on-time on electrode material migration during EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)