Temperature distribution in copper electrode during electrical discharge machining process

QR Code

Temperature distribution in copper electrode during electrical discharge machining process

This paper reports on a new method used to estimate the spark radius in the gap during electrical discharge machining (EDM). This method combines the heat flux and energy equations of the copper electrode. The energy partition between workpiece and electrode (tool) due to EDM process was estimated u...

Full description

Bibliographic Details
Main Authors:	Abdulkareem, Suleiman, Khan, Ahsan Ali, Shah, Qasim Hussain, Konneh, Mohamed
Format:	Article
Language:	English English
Published:	Penerbit UHTM 2017
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/56409/ http://irep.iium.edu.my/56409/1/Temperature%20distribution.pdf http://irep.iium.edu.my/56409/7/56409_Temperature%20distribution%20in%20copper%20electrode_SCOPUS.pdf

Similar Items

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during edm of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during EDM of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrode cooling on recast layers and micro crack in EDM of titanium
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Study of material removal rate and electrode wear ratio for micro electrical discharge milling of AISI 420 and Stavax ESR
by: Mohammad, Yeakub Ali, et al.
Published: (2009)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Cooling effect on electrode and process parameters in EDM
by: Abdulkareem, Suleiman, et al.
Published: (2010)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

A study on material removal rate during EDM with tantalum carbide-copper compacted electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

A comparative study on work surface hardness EDMed by Ta-C powder compacted and copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Investigation of the influence of the properties of the work and tool materials on performance level of Electrical Discharge Machining (EDM) process
by: A.K.M., N. Amin, et al.
Published: (1997)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Effect of gap voltage and pulse-on time on material removal rate for electrical discharge machining of Al2O3
by: Moudood, M. A., et al.
Published: (2015)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
by: Khan, Ahsan Ali, et al.
Published: (2013)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)