Dimensional accuracy of micro-electro discharge milling

QR Code

Dimensional accuracy of micro-electro discharge milling

This paper investigates the dimensional accuracy and tool wear rate (TWR) in micro electro discharge (micro-ED) milling of stainless steel (S304) workpiece and tungsten as the tool electrode with control parameter; voltage and feed rate. Dimensional accuracy is represented by the difference of micro...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Abd. Rahman, Mohamed, Zunairi, Siti Nur Zuhaida, Banu, Asfana
Format:	Proceeding Paper
Language:	English English
Published:	IOP Publishing 2017
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/56355/ http://irep.iium.edu.my/56355/7/56355.pdf http://irep.iium.edu.my/56355/13/56355-Dimensional%20Accuracy%20of%20Micro-Electro%20Discharge%20Milling_SCOPUS.pdf

Similar Items

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Material removal rate of zirconia in electro discharge micromachining
by: Asfana, Banu, et al.
Published: (2015)

Micro wire electro discharge grinding: optimization of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Study of material removal rate and electrode wear ratio for micro electrical discharge milling of AISI 420 and Stavax ESR
by: Mohammad, Yeakub Ali, et al.
Published: (2009)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Investigation of surface roughness and material removal rate for high speed micro end milling on PMMA
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2015)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Micro-edm for micro-channel fabrication on nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2014)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Effect of gap voltage and pulse-on time on material removal rate for electrical discharge machining of Al2O3
by: Moudood, M. A., et al.
Published: (2015)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of micro-EDM parameters on material removal rate of nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2011)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Investigation of vibration in micromilling with MQL: S/N ratio analysis
by: Hussin, Muhammad Shaffiq, et al.
Published: (2020)

Investigation of surface roughness in micro-EDM of nonconductive ZrO2 ceramic with powder mixed dielectric fluid
by: Sabur, Abdus, et al.
Published: (2015)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Investigation of the influence of the properties of the work and tool materials on performance level of Electrical Discharge Machining (EDM) process
by: A.K.M., N. Amin, et al.
Published: (1997)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)