Thermal performance of fined plate mini-channel heat sink

QR Code

Thermal performance of fined plate mini-channel heat sink

This paper presents fined plate minichannel heat sink numerically under forced convection. Two geometries, flat plate and fined plat heat sinks have been drawn by solidworks, then imported to Starccm+ for simulation. The plate was 45 mm width and 55mm length and the fined heat sink has fins with 3 m...

Full description

Bibliographic Details
Main Authors:	Mohamed Ali, Suliman Mohamed, Faris, Waleed Fekry, Ismail, Ahmad Faris, Khan, Sher Afghan
Format:	Article
Language:	English
Published:	International Organization of Scientific Research ( IOSR ) 2016
Subjects:	TJ210.2 Mechanical devices and figures. Automata. Ingenious mechanism. Robots (General)
Online Access:	http://irep.iium.edu.my/54300/ http://irep.iium.edu.my/54300/1/Suleman-Faris.pdf

Similar Items

Numerical investigation of non-dimensional constant and empirical relation representing Nusselt profile non-uniformity
by: Mohd, Umair Siddiqui, et al.
Published: (2020)

Impedance based detection of delamination in composite structures
by: Djemana, Mohamed, et al.
Published: (2017)

Dynamics and control of quadcopter using linear model predictive control approach
by: Islam, M, et al.
Published: (2017)

Book shelving robotics
by: Salami, Momoh Jimoh Eyiomika, et al.
Published: (2011)

Smart tendon actuated flexible actuator
by: Billah, Md. Masum, et al.
Published: (2015)

Investigation on data extraction trends for snake robot
by: Khan, Md. Raisuddin, et al.
Published: (2014)

Mobility determination and estimation based on smartphones-review of sensing and system
by: Aljeroudi, Yazan, et al.
Published: (2015)

CPG-based control system for flexible snake robot locomotion
by: Khan, Md. Raisuddin, et al.
Published: (2014)

Development and initial testing of an autonomous surface vehicle for shallow water mapping
by: Mat Idris, Mohamad Hilmi, et al.
Published: (2015)

Multiplexing of unformatted asynchronous serial data to a single NMEA 0183 protocol compliance data-stream for autonomous surface vehicles data logging
by: Mat Idris, Mohamad Hilmi, et al.
Published: (2015)

Accelerated learning programme for robotic competition
by: Othman, Azam, et al.
Published: (2017)

Gripping motion of artificial hand using EMG signal
by: Mat Rosly, Muhammad Hadi, et al.
Published: (2016)

Human-friendly robot and bio-inspired robot: new challenge in robotics
by: Rahman, Md. Mozasser
Published: (2016)

Optimization of CO2 production rate for firefighting robot applications using response surface methodology
by: Ajala, M. T., et al.
Published: (2018)

Dynamic tuning of torsional transmissibility using magnetorheological elastomer: Modelling and experimental verification
by: Hashi, Hamza, et al.
Published: (2016)

Investigating negative capacitance shunt circuit for broadband vibration damping and utilizing ACO for optimization
by: Wahid, Azni Nabela, et al.
Published: (2016)

Internet based troubleshooting and monitoring system of industrial robots
by: Rahman, Md Mozasser, et al.
Published: (2017)

Introduction to robotic design: theory, hardware and programming
by: Rahman, Md. Mozasser
Published: (2017)

Upper-limb impedance parameters-based model for motor recovery
by: Htoon, Zaw Lay, et al.
Published: (2017)

Assessing the effect of persuasive robots interactive social cues on users’ psychological reactance, liking, trusting beliefs and compliance
by: Ghazali, Aimi Shazwani, et al.
Published: (2019)

Assist-as-needed control strategy for upper-limb rehabilitation based on subject’s functional ability
by: Ahmed Mounis, Shawgi Younis, et al.
Published: (2019)

PID and inverse-model-based control of a twin rotor system
by: Toha, Siti Fauziah, et al.
Published: (2011)

Visual tracking and servoing of human face for robotic head Amir-II
by: Shafie, Amir Akramin, et al.
Published: (2010)

Graphical user interface for Humanoid Head Amir-II
by: Shafie, Amir Akramin, et al.
Published: (2010)

Development of a flexible video analysis system for motion detection and alarm generation
by: Shafie, Amir Akramin, et al.
Published: (2010)

Foreground segmentation-based human detection with shadow removal
by: Hafiz, Fadhlan, et al.
Published: (2010)

Advance video analysis system and its applications
by: Ali, Md. Hazrat, et al.
Published: (2010)

Kinematics model of snake robot considering snake scale
by: Khan, Md. Raisuddin, et al.
Published: (2010)

A collaborative navigation algorithm for multi-agent robots in autonomous reconnaissance mission
by: Ahmed, Mohiuddin, et al.
Published: (2010)

Development of an efficient CVT using electromechanical system
by: Shafie, Amir Akramin, et al.
Published: (2009)

Development and performance evaluation of an ultra precision ELID grinding machine
by: Saleh, Tanveer, et al.
Published: (2007)

Development of an on-machine profile measurement system in ELID grinding for machining aspheric surface with software compensation
by: Sazedur Rahman, M., et al.
Published: (2008)

A multiprocess machine tool for compound micromachining
by: Rahman, M., et al.
Published: (2010)

Development of a three dimensional visualization tool for spacecraft attitude and orbital dynamics using telemetry data
by: Abdelrahman, Mohammad
Published: (2012)

A novel navigation algorithm for collaborative multi robots
by: Ahmed, Mohiuddin, et al.
Published: (2010)

Geometrical analysis on BIOLOID humanoid system standing on single leg
by: Akhtaruzzaman , Md., et al.
Published: (2011)

A novel gait for toddler biped and its control using PIC 16F877A
by: Akhtaruzzaman, Md., et al.
Published: (2011)

An attempt to develop a Biped Intelligent Machine BIM-UIA
by: Akhtaruzzaman, Md., et al.
Published: (2011)

Optimal tour constructions for multiple mobile robots
by: Shafie, Amir Akramin
Published: (2011)

Multi-agent application: a novel algorithm for hexapod robots gait transitions
by: A. K. M. Mohiuddin, Md. Yahya, et al.
Published: (2010)