Transfer and heating mechanisms of a curry puff vending machine

QR Code

Transfer and heating mechanisms of a curry puff vending machine

This paper focuses on the design and development of the transfer and heating mechanisms of a curry puff vending machine. The vending machine contains frozen pre-cooked curry puffs that are packed in containers and require heating process before being dispensed to the consumers. The transfer mechani...

Full description

Bibliographic Details
Main Authors:	Mohd Ali, Muhamad Khalid, Zainul Azlan, Norsinnira, Ali, Muhammad Aminuddin Anwar
Format:	Article
Language:	English English
Published:	Asian Research Publishing Network (ARPN) 2016
Subjects:	TJ Mechanical engineering and machinery TK Electrical engineering. Electronics Nuclear engineering
Online Access:	http://irep.iium.edu.my/51751/ http://irep.iium.edu.my/51751/1/transfer_and_heating_mechanisms.pdf http://irep.iium.edu.my/51751/4/51751-Transfer_and_heating_mechanisms_of_a_curry_puff_vending_machine_SCOPUS.pdf

Similar Items

Design of a curry puff making machine
by: Ibrahim, Imran
Published: (2010)

Smart vending machine counter using IOT
by: Ali Ali, Athir Jaafar
Published: (2020)

Design of iris mechanism for flexion and extension training in hand rehabilitation
by: Ali, Muhammad Aminuddin Anwar, et al.
Published: (2016)

Design and implementation of instant noodles vending machine
by: Muhammad , Mahbubur Rashid
Published: (2011)

Development of vending machine with prepaid payment method
by: Amar Safuan, Alyusi
Published: (2008)

Layout design for food safety improvement of frozen crispy chicken curry puff processing
by: Rosli, Nur Amira, et al.
Published: (2022)

Vending machine’s heat transfer for par-fried dough products
by: Naim, Mohd Nazli, et al.
Published: (2024)

Microbial shelf-life estimation of frozen crispy chicken curry puff under accelerated storage conditions
by: Rosli, Nur Amira, et al.
Published: (2024)

Automated vending machine system
by: Mohammad Ali, Mohd. Hasyim
Published: (2007)

Development of low-cost robotic hands for introduction to mechatronics engineering courses
by: Ali, Muhammad Aminuddin Anwar, et al.
Published: (2016)

Modeling and control of electrohydraulic robot manipulator
by: Zainul Azlan, Norsinnira
Published: (2006)

Human lower arm analysis during different eating activities
by: Hussain, Zakia, et al.
Published: (2017)

Adaptive impedance control for unknown time-varying environment position and stiffness
by: Zainul Azlan , Norsinnira, et al.
Published: (2013)

FAT based adaptive impedance control for unknown environment position
by: Zainul Azlan, Norsinnira, et al.
Published: (2012)

Modeling and control of compact anthropomorphic robot finger
by: Zainul Azlan, Norsinnira, et al.
Published: (2011)

Experimental studies of position control of linkage based robotic finger
by: Zainul Azlan, Norsinnira, et al.
Published: (2011)

Adaptive impedance control for unknown non-flat environment
by: Zainul Azlan, Norsinnira, et al.
Published: (2013)

Anthropomorphic finger with optimized geometric parameters for pinching and grasping tasks
by: Zainul Azlan, Norsinnira, et al.
Published: (2012)

Adaptive backstepping position control of pneumatic anthropomorphic robotic hand
by: Farag, Mohannad, et al.
Published: (2015)

Design and development of an anthropomorphic shoe-tying robot
by: Ramli, Mohd Syamsul, et al.
Published: (2014)

Control of cooperative manipulators in holding deformable objects
by: Alkathiri, A A, et al.
Published: (2017)

Adaptive sliding mode control with radial basis function neural network for time dependent disturbances and uncertainties
by: Shanta, Mst. Nafisa Tamanna, et al.
Published: (2016)

Function approximation technique based sliding mode controller adaptive control of robotic arm with time-varying uncertainties
by: Mst., Nafisa Tamanna Shantaa, et al.
Published: (2015)

Experimental Investigation of Heat Transfer Over Machining Surfaces Using Infrared Camera
by: Nadaraj, Sarvesh
Published: (2015)

Adaptive control of robotic arm carrying uncertain time-varying payload based on function approximation technique
by: Zainul Azlan, Norsinnira, et al.
Published: (2014)

Design and implementation of instant noodles vending machine
by: Rashid, Muhammad Mahbubur
Published: (2011)

Experimental determination of convective heat transfer coefficient in wire electro discharge machining
by: Nadiah Waznah, Zabidi
Published: (2008)

Towards a predictive model of Ca²⁺ puffs
by: Thul, Ruediger, et al.
Published: (2009)

Startup, heat transfer, and flow characteristics of a ⊥-shaped oscillating heat pipe for application in a hybrid battery thermal management system
by: Lu, Hongkun, et al.
Published: (2025)

Nanocellulose as heat transfer liquid in heat exchanger
by: F., Benedict, et al.
Published: (2019)

Business Plan for Vending Machines installation in Indian Universities
by: Thakral, Aman
Published: (2016)

Modeling bearing temperature of DC machine in no-load condition using transfer function
by: M. S., Mat Jahak, et al.
Published: (2024)

Investigation of the effect of different materials on convective heat transfer
by: A. A., Ibrahim, et al.
Published: (2020)

A review on heat transfer enhancement in a heat exchanger
by: Gobinathan, Sashwin Nair, et al.
Published: (2024)

Sistem Kawalan Vending Machine (VMCS) / Norhaidah Abd. Ghani
by: Norhaidah , Abd. Ghani
Published: (2002)

Design of a low cost coin acceptor for vending machine
by: Ho Chee Leong, Richmond Chris, et al.
Published: (2021)

IoT-Based Reverse Vending Machine (RVM) for recycle station
by: Mohd Adzaharee, Muhammad Sallehuddin, et al.
Published: (2021)

Heat transfer characteristics of car radiator using tri-hybrid nanocoolant
by: Anwar Ilmar, Ramadhan, et al.
Published: (2020)

Heat transfer to graphene nanoplatelets and metaloxides-studies in thermophysical properties and particle characterization / Solangi Khalid Hussain
by: Solangi Khalid , Hussain
Published: (2016)

Numerical Study Of Plate Heat Exchanger For Erema Machine
by: Awang, Muhamad Haidar
Published: (2019)