Optimization of surface quality of mild steel machined by wire EDM using simulated annealing algorithm

QR Code

Optimization of surface quality of mild steel machined by wire EDM using simulated annealing algorithm

One of the main machining characteristics that play vital role in determining the quality of engineering components is surface integrity. The fatigue strength, corrosion and wear resistance is enhanced by good quality surfaces of the work piece. The purpose of this research is investigating and opti...

Full description

Bibliographic Details
Main Authors:	Khan, Ahsan Ali, Al Hazza, Muataz Hazza Faizi, Che Daud, Mohd Radzi, Mohamad Kamal, Nor Shahirah
Format:	Proceeding Paper
Language:	English English
Published:	The Institute of Electrical and Electronics Engineers, Inc. 2016
Subjects:	T Technology (General)
Online Access:	http://irep.iium.edu.my/46490/ http://irep.iium.edu.my/46490/1/46490_Optimization.pdf http://irep.iium.edu.my/46490/4/46490_Optimization_of_Surface_Quality_of_Mild_Steel_Machined_Scopus.pdf

Similar Items

Analyzing and modeling the influence of workpiece thickness on geometry of slot machining wire EDMs
by: Khan, Ahsan Ali, et al.
Published: (2016)

Exploration of EDM assisted CNT in micro machining using statistical approach
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2016)

Exploration of EDM assisted CNT in micro machining using statistical approach
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

A study on capabilities of different electrode materials during electrical discharge machining (EDM)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Performance of electrical discharge machining (EDM) with nickel added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Energy cost optimization in high speed hard turning using simulated annealing algorithm
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Improvement of surface quality using silicon carbide powder added dielectric fluid during EDM
by: Khan, Ahsan Ali, et al.
Published: (2017)

Simulating the electrical and thermal conductivity in EDM die sinking of Cu-TaC compact electrodes using neural network
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Surface integrity of mild steel in wire electrical discharge machining
by: Mohamad Suffi, Kamari
Published: (2010)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Multi objective optimisation for high speed end milling using simulated annealing algorithm
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Dimensional accuracy in dry micro wire electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Surface integrity of mild steel in die-sinking electrical discharge machine (EDM)
by: Muhamad Haniffah, Ghafar
Published: (2010)

Modeling the effect of CNT concentration in dielectric fluid on EDM performance using neural network
by: Khan, Ahsan Ali, et al.
Published: (2016)

Development of a new model for predicting EDM properties of Cu-TaC compact electrodes based on artificial neural network method
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of EDM of mild steel with Ta-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Modeling the electrical parameters in EDM process of Ti6Al4V alloy using Neural Network method
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Statistical analysis of tooling cost in high speed end milling for hardened steel
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2016)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Machining time stimulating in high speed hard tuning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2009)

Influence of current, spark on-time and off-time on electrode wear during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Experimental investigations in high-speed hard turning of AISI 4340 steel using mixed ceramic
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Investigation of effect of machine layout on productivity and utilization level: what if simulation approach
by: Bourini, Islam Faisal, et al.
Published: (2018)

New tool life models in turning hardened steel AISI 4340 under high cutting speed
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Design a tacit knowledge sharing system
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Flank wears simulation by using back propagation neural network when cutting hardened H-13 steel in CNC End Milling
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)