Wear analysis of ZTA-Mgo ceramic cutting inserts on stainless steel 316L machining

QR Code

Wear analysis of ZTA-Mgo ceramic cutting inserts on stainless steel 316L machining

The performance of zirconia toughened alumina with addition of MgO additives is investigated. Optimized composition of MgO at 1.1 wt% was used in the composition with alumina/yittria stabilized zirconia (YSZ). The composition was mixed, uniaxially pressed into rhombic 80º cutting inserts with 0.8...

Full description

Bibliographic Details
Main Authors:	Mohd Ali, Afifah, Ahmad Azhar, Ahmad Zahirani, Ratnam, Mani Maran, Ahmad, Zainal Arifin
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2015
Subjects:	Q Science (General)
Online Access:	http://irep.iium.edu.my/45857/ http://irep.iium.edu.my/45857/1/2015_-_IXCRI%2C_AMR%2C_Afifah.pdf

Similar Items

Tetragonal and monoclinic phase transformation of ZTA-MgO ceramic cutting tool by machining process
by: Mohd Ali, Afifah, et al.
Published: (2017)

Tetragonal and monoclinic phase transformation of ZTA-MgO ceramic cutting tool by machining process
by: Mohd Ali, Afifah, et al.
Published: (2017)

Effects of TiN single layer coating on the wear of ZTA cutting inserts and surface roughness of workpiece
by: Ahmad Azhar, Ahmad Zahirani, et al.
Published: (2017)

High wear Resistant Ceramic Cutting inserts With Enhanced Toughness For High-Speed Machining
by: Ahmad, Zainal Arifin, et al.
Published: (2016)

Hardness and fracture toughness analysis of ZTA–SWCNT ceramic cutting inserts
by: Hamidon, Nor Ezzati, et al.
Published: (2019)

The effect of cutting parameters on the performance of ZTA-MgO cutting tool
by: Mohd Ali, Afifah, et al.
Published: (2018)

The relationship between microstructure and fracture toughness of zirconia toughened alumina (ZTA) added with MgO and CeO2
by: Rejab, Nik Akmar, et al.
Published: (2013)

The relationship of cutting chip type, length and thickness to wear of Zirconia Toughened Alumina Added with Magnesium Oxide (ZTA-MgO) cutting tool
by: Mohd Ali, Afifah, et al.
Published: (2018)

XRD investigation of the effect of MgO additives on ZTA-TiO2 ceramic composites
by: Ahmad Azhar, Ahmad Zahirani, et al.
Published: (2018)

SYNTHESIS AND CHARACTERIZATION OF MgO-Cr2O3-ZTA CUTTING TOOL MATERIAL
by: Ahmad Azhar, Ahmad Zahirani
Published: (2013)

Effects of MgO addition on the phase, mechanical properties, and microstructure of zirconia-toughened alumina added with CeO2 (ZTA–CeO2) ceramic composite
by: Rejab, Nik Akmar, et al.
Published: (2014)

Study On The Development Of Ceramic Cutting Tool (ZTA / ZTA-MGO) And Its Machining Performance In Slot Milling
by: Hassan, Mohd Nor Hakim
Published: (2010)

Study On The Development Of Ceramic Cutting Tool (zta I Zta-mgo) And Its Machining Performance In Slot Milling
by: Hassan, Mohd Nor Hakim
Published: (2010)

Analysis on physical and microstructural properties of ZTA-SWNT ceramic cutting tool
by: Abdul Molok, Salma, et al.
Published: (2019)

Wear Resistance Performance Of Zirconia Toughened Alumina (ZTA) Cutting Tool Added With MgO and CeO2
by: Ali, Afifah Mohd.
Published: (2016)

Role of MgO nanoparticles on zirconia-toughened alumina-5 wt-% CeO2 ceramics mechanical properties
by: Rejab, Nik Akmar, et al.
Published: (2016)

The influence of in-situ formation of hibonite on the properties of zirconia toughened alumina (ZTA) composites
by: Ibrahim Sktani, Zhwan Dilshad, et al.
Published: (2014)

The flank wear optimisation of 316 Stainless Steel using response surface method in dry-down milling using carbide insert
by: Nurul Hidayah, Razak, et al.
Published: (2022)

Tool Wear Measurement Using Machine Vision.
by: Ratnam, Mani Maran
Published: (2008)

Experimental of Hot Machining for Stainless Steel 316L Cutting Process
by: Cholis, N., et al.
Published: (2024)

The effects of CeO2 addition on the physical and microstructural properties of ZTA-TiO2 ceramics composite
by: Ahmad Azhar, Ahmad Zahirani, et al.
Published: (2019)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Tool deterioration of 316 stainless steel in dry down-milling using carbide insert
by: Nur Farziana, Husein, et al.
Published: (2021)

Microwave sintering of zirconia-toughened alumina (ZTA)-TiO2-Cr2O3 ceramic composite: the effects on microstructure and properties
by: Manshor, Hanisah, et al.
Published: (2017)

Effect of cutting speed on Bio-corrosion of AISI 316L stainless steel
by: Saliza Azlina, O., et al.
Published: (2016)

Experimental Characterization And Neural Network Prediction Of Dynamic Behavior Of Zta With Srco3 And Mgo
by: Arab, Ali
Published: (2016)

Effects of Cr2O3 addition on the phase, mechanical properties, and microstructure of zirconia-toughened alumina added with TiO2 (ZTA–TiO2) ceramic composite
by: Manshor, Hanisah, et al.
Published: (2016)

Effect of Titania (TiO2) Addition to Zirconia Toughened Alumina (ZTA) Phases, Hardness and Microstructure
by: Manshor, Hanisah, et al.
Published: (2015)

Effect of Machining Parameters on Tool Wear and Hole Quality of AISI 316L Stainless Steel in Conventional Drilling
by: Sultan, A., et al.
Published: (2015)

Tribo-electrochemical behaviour of 316L stainless steel: The effects of contact configuration, tangential speed, and wear mechanism
by: Salasi, Mobin, et al.
Published: (2015)

Multi-Objective Optimization of Cutting Parameters to Minimize Power Consumption in Dry Turning of Stainless Steel 316
by: Bagaber, Salem Abdullah, et al.
Published: (2017)

Performance evaluation of nitrogen gas-assisted laser cutting on 316L austenitic stainless steel plate
by: Abd. Halim, Shahrizal
Published: (2010)

Wear behaviour of surface alloyed duplex stainless steel containing SiC ceramic particles
by: Paijan, Lailatul Harina, et al.
Published: (2017)

Cyclic thermomechanical testing of 316 stainless steel
by: Buss, T.M., et al.
Published: (2015)

Study of cutting force and surface roughness on drilling stainless steel 316L under various coolant condition
by: Kamdani, K., et al.
Published: (2018)

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Comparison machining performance of Al2 O3 , ZTA and ZTA doped Cr2 O3 cutting tools on AISI 1045
by: T., Norfauzi, et al.
Published: (2019)

Experimental determination of creep fatigue life of 316L stainless steel pipe
by: Mohammad, Khairul Azhar
Published: (2011)

Wear of coated carbide insert in machining of mild steel
by: Mohamad Saiful, Izwan Busu
Published: (2010)

Characterization Of β-TCP Coated On Stainless Steel 316
by: Ariff, Ummi Fatisya Ain
Published: (2022)