Effect of powder concentration on EDM performance during machining mild steel

QR Code

Effect of powder concentration on EDM performance during machining mild steel

This research work describes the effect of powder concentration in dielectric fluid during electrical discharge machining (EDM) of mild steel on material removal rate (MRR), electrode wear rate (EWR) and work surface roughness (Ra). The machining parameters studied in this research are current (4.5A...

Full description

Bibliographic Details
Main Authors:	Khan, Ahsan Ali, Wahid Azmi, Nurfarah, Odenan, Mohd Azim, Mohd Zain, Zakaria
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2015
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/44117/ http://irep.iium.edu.my/44117/1/AMR.1115.7_%282%29_online_2015.pdf

Similar Items

Features of EDM of mild steel with Ta-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Influence of current, spark on-time and off-time on electrode wear during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrodes for EDM
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Optimization of process parameters on EDM milling of stainless steel AISI 304
by: A.K.M, Asif Iqbal, et al.
Published: (2011)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Surface modification by EDM using Co-Cr sintered powder metallurgy electrode
by: Khan, Ahsan Ali, et al.
Published: (2012)

Surface modification by EDM using CO-CR sintered powder metallurgy electrod
by: Khan, Ahsan Ali, et al.
Published: (2012)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

A comparative study on work surface hardness EDMed by Ta-C powder compacted and copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Performance of PM compacted Cu-TaC electrodes during EDM
by: Mohammed, Baba Ndaliman, et al.
Published: (2011)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

Modeling the effect of CNT concentration in dielectric fluid on EDM performance using neural network
by: Khan, Ahsan Ali, et al.
Published: (2016)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Developments in EDM process variables
by: Khan, Ahsan Ali, et al.
Published: (2011)

Role of current, voltage and spark on-time on electrode material migration during EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of size and shape of electrodes on the performance of EDM
by: Khan, Ahsan Ali, et al.
Published: (2008)

Determination of influential factors on EDMed surface properties using Plackett-Burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Determination of influential factors on edmed surface properties using plackett-burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Influence of electrode cooling on material migration among the electrodes during edm of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during EDM of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)