Hybrid rocket performance with varying additive concentrations

QR Code

Hybrid rocket performance with varying additive concentrations

A hybrid rocket motor represents a compromise between a solid rocket motor and a liquid rocket motor in terms of its performance. In addition, hybrid rockets are featured by throttling capability, increased safety, moderate cost and benign environmental impact. However, low regression rate is a majo...

Full description

Bibliographic Details
Main Authors:	Kafafy, Raed, Azami, Muhammad Hanafi, Idres, Moumen
Format:	Proceeding Paper
Language:	English
Published:	2013
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/44046/ http://irep.iium.edu.my/44046/1/2013-Performance_of_Hybrid_Rocket_with_Varying_Additive.pdf

Similar Items

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Propellant development for small rockets
by: Rahmat, Mohd. Zaki Yamani, et al.
Published: (2008)

Determining Potassium Nitrate performance as solid rocket propellant for rocket engine
by: Dahalan, Md. Nizam, et al.
Published: (2003)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Development of solid rocket propulsion system at UTM
by: Mohd. Jaafar, Mohammad Nazri, et al.
Published: (2004)

Development of solid rocket propulsion system at UTM
by: Mohd. Jaafar, Mohammad Nazri, et al.
Published: (2004)

Development of a 100-n hydrogen peroxide rocket engine
by: Krishnan, S., et al.
Published: (2008)

Design and development of a hydrogen-peroxide rocket-engine facility
by: Krishnan, Subramaniam, et al.
Published: (2010)

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Modeling of compression systems
by: Idres, Moumen
Published: (2011)

Constrained model predictive control for proton exchange membrane fuel cell
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Fuel cell starvation control using model Predictive technique with laguerre and exponential weight functions
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

Design of an autopilot for an autonomous unmanned aerial vehicle
by: Idres, Moumen, et al.
Published: (2011)

Hybrid-inspired coolant additive for radiator application
by: Benedict Foo, Jing Siong
Published: (2020)

Performance analysis of a small capacity horizontal axis wind turbine using QBlade
by: Ali, Said, et al.
Published: (2019)

Surge and rotating stall
by: Idres, Moumen
Published: (2011)

Compressor models
by: Idres, Moumen
Published: (2011)

Towards a numerical simulation of supersonic mixing & combustion
by: Kamel, Mohammed, et al.
Published: (2013)

Numerical simulation and validation of high-speed turbulent and chemically-reacting flows
by: Kamel, Mohammed, et al.
Published: (2015)