Experimental investigation of the performance of flutter-based microgenerators

QR Code

Experimental investigation of the performance of flutter-based microgenerators

Many wind harvesters have a high cut-in speed which is not available in many locations over long periods of time. The average wind speed round the year at most locations is 3-5 m/s. A novel and inexpensive low wind speed harvester design is proposed and tested in this work, winds and artificial airf...

Full description

Bibliographic Details
Main Authors:	Kafafy, Raed, Javeed, Abdulhakeem, Ihsan, Sany Izan, Idres, Moumen
Format:	Proceeding Paper
Language:	English
Published:	2013
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/44045/ http://irep.iium.edu.my/44045/1/2013-Experimental_Investigation_of_the_Performance_of_Flutter-Based_Microgenerators.pdf

Similar Items

Modeling and analysis of flutter-based thin-film cantilever microgenerator
by: Abdul Hakim, Javid, et al.
Published: (2015)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Modeling of compression systems
by: Idres, Moumen
Published: (2011)

A first course in control systems
by: Faris, Waleed Fekry, et al.
Published: (2009)

Ride performance analysis of half-car model for semi-active system using RMS as performance criteria
by: Ihsan, Sany Izan, et al.
Published: (2009)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

A comparative study on MEMS piezoelectric microgenerators
by: Md Ralib @ Md Raghib, Aliza 'Aini, et al.
Published: (2010)

A comparative ride performance and dynamic analysis of passive and semi-active suspension systems based on different vehicle models
by: Faris, Waleed Fekry, et al.
Published: (2009)

Constrained model predictive control for proton exchange membrane fuel cell
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Fuel cell starvation control using model Predictive technique with laguerre and exponential weight functions
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Investigation of Malaysian low earth orbits for remote sensing applications
by: Okasha, Mohamed Elsayed Aly Abd Elaziz, et al.
Published: (2017)

Design of an autopilot for an autonomous unmanned aerial vehicle
by: Idres, Moumen, et al.
Published: (2011)

An Experimental Investigation On The Combustion And Performance Of An HCCI-DI Engine
by: Hasyuzariza, M. Tobib, et al.
Published: (2019)

Experimental investigation on performance of solar-powered attic ventilation
by: F., Basrawi, et al.
Published: (2018)

Performance analysis of a small capacity horizontal axis wind turbine using QBlade
by: Ali, Said, et al.
Published: (2019)

Analysis of semi-active suspension systems for four-axles off-road vehicle using half model
by: Faris, Waleed Fekry, et al.
Published: (2009)

Improving the efficiency of micronozzle by heated sidewalls
by: Hameed, Amar Hasan, et al.
Published: (2011)

Surge and rotating stall
by: Idres, Moumen
Published: (2011)