Mode I stress intensity factor for a cracked plate with an integrated piezoelectric actuator

QR Code

Mode I stress intensity factor for a cracked plate with an integrated piezoelectric actuator

The fracture performance of cracked structures is dominated by singular stress in the crack tip vicinity. In fracture mechanics, most interest is focussed on stress intensity factors, which describe the singular stress field ahead of a crack tip and govern fracture of structures when a critical stre...

Full description

Bibliographic Details
Main Authors:	Abuzaid, Ahmed, Hrairi, Meftah, Shaik Dawood, Mohd. Sultan Ibrahim
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2015
Subjects:	TA165 Engineering instruments, meters, etc. Industrial instrumentation TA630 Structural engineering (General)
Online Access:	http://irep.iium.edu.my/44040/ http://irep.iium.edu.my/44040/1/44040_-_Mode_I_stress_intensity_factor_for_a_cracked_plate_with_an_integrated_piezoelectric_actuator.pdf

Similar Items

Finite element simulation of electro-mechanical impedance technique
by: Tahmasebpour, Kamyar, et al.
Published: (2015)

Design and optimization of a micro capacitive pressure sensor
by: Tahmasebpour, Kamyar, et al.
Published: (2013)

Derivation of stress intensity factor for a cracked plate with an integrated piezoelectric actuator
by: Abuzaid, Ahmed, et al.
Published: (2014)

Pulsed magnetic flux leakage techniques for crack detection and characterisation
by: Sophian, Ali, et al.
Published: (2006)

Three-dimensional static shape control analysis of composite plates using distributed piezoelectric actuators
by: Shaik Dawood, Mohd. Sultan Ibrahim, et al.
Published: (2008)

Evaluating the reduction of stress intensity factor in center-cracked plates using piezoelectric actuators
by: Abuzaid, Ahmed, et al.
Published: (2018)

Delamination control in composite beams using piezoelectric actuators
by: Iannucci, L, et al.
Published: (2009)

Development of an angle sensor using optical polarizer
by: Rana, M. M., et al.
Published: (2015)

Data fusion for defect characterisation using a dual probe system
by: Edwards, R.S., et al.
Published: (2008)

A feature extraction technique based on principal component analysis for pulsed Eddy current {NDT}
by: Sophian, Ali, et al.
Published: (2003)

Reduction of lift-off effects for pulsed eddy current NDT
by: Tian, Gui Yun, et al.
Published: (2005)

Feature extraction and selection for defect classification of pulsed eddy current NDT
by: Chen, Tianlu, et al.
Published: (2008)

Defect classification using a new feature for pulsed eddy current sensors
by: Tian, Gui Yun, et al.
Published: (2005)

Dual EMAT and PEC non-contact probe: applications to defect testing
by: Edwards, R.S., et al.
Published: (2006)

Optical thermal imaging for breast cancer diagnosis
by: Zubir, Nazira, et al.
Published: (2016)

Tendon bioreactor
by: Zubir, Nazira, et al.
Published: (2016)

Electrochemical biosensor : amperometric – glucose sensor
by: Zubir, Nazira
Published: (2015)

Setting up a new Radiology Center Technology for improvement : Data mining (Image Mining Technique)
by: Zubir, Nazira
Published: (2016)

A low normal force contact using photolithography and Ni-Co electro fine forming technology
by: Bhuiyan, Moinul, et al.
Published: (2009)

Development of optical switch using SMA coil and magnetic latch
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2003)

MEMS and EFF Technology based micro connector for future miniature devices
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2013)

Design and fabrication stable LNF contact for future IC application
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2013)

Development and optimization of a low normal force contact
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2013)

Design and Implementation of Fuzzy Based Person Following Mobile Robot1
by: Rashid, Muhammad Mahbubur, et al.
Published: (2012)

A novel signal diagnosis technique using pseudo complex-valued autoregressive technique
by: Aibinu, Abiodun Musa, et al.
Published: (2011)

Design and development of a smart window blind controlling system
by: Bhuiyan, Moinul, et al.
Published: (2014)

Development of robotic arm plotter for disable people
by: Bhuiyan, Moinul, et al.
Published: (2014)

EMC 201(3) - MEASUREMENT AND INSTRUMENTATION OKT-NOV 07.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2007)

Wattmeter reading with the range of IoT's communication
by: Azmi, NorIskandar, et al.
Published: (2020)

IoT based black box for vehicles
by: Aldholay, Mohammed Hussein Hassan, et al.
Published: (2020)

IoT and LoRaWAN
by: Ashraf, Ahmed, et al.
Published: (2020)

Effect of soaking time to the bending strength of porcelain with palm oil fuel ash
by: Noh, Mohamad Zaky, et al.
Published: (2018)

Sensor material characterisation for magnetometer application
by: Zinal, Nabiah
Published: (2004)

Comparison machining performance of Al2 O3 , ZTA and ZTA doped Cr2 O3 cutting tools on AISI 1045
by: T., Norfauzi, et al.
Published: (2019)

Development of groundwater filtration system using multiseries media
by: Abdul Aziz, Nor Izzah
Published: (2022)

Effect of bonded composite patch on the stress intensity factor for a center cracked plate
by: Aabid, Abdul, et al.
Published: (2019)

Modeling approach to evaluating reduction in stress intensity factor in center-cracked plate with piezoelectric actuator patches
by: Abuzaid, Ahmed, et al.
Published: (2017)

Intelligent control of grain drying process using fuzzy logic controller
by: Mansor, Hasmah, et al.
Published: (2010)

Design and development of Multipurpose Educational and Research Platform (MERP) for learning control & IOT technologies
by: Embong, Abd Halim, et al.
Published: (2019)

Thermal properties of polymer materials in laser sintering process
by: Pham, Duc Trung, et al.
Published: (2011)