Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations

QR Code

Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations

The paper reports the research on the improvement of tool wear resistant of Titanium Carbide (TiC) cutting tool after microwave post sintering treatment. Titanium Carbide square milling insert was microwave sintered at 600°C with 15 minutes of holding time. The face milling operations were conducted...

Full description

Bibliographic Details
Main Authors:	Iqbal, Mohammad, Ariff, Tasnim Firdaus, Mat Roseh, Mohd Shahrul Fahmi, Al Hazza, Muataz Hazza Faizi, Hilmy, Irfan, -, Suryanto
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2015
Subjects:	T Technology (General) TN600 Metallurgy TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/44024/ http://irep.iium.edu.my/44024/1/44024_-_Effect_of_microwave_sintering_treatment_to_the_flank_wear_of_titanium_carbide_tools_in_milling_operations.pdf

Similar Items

Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
by: Iqbal, Mohammad, et al.
Published: (2014)

Flank Wear Modeling in High Speed Hard Turning by using artificial Neural Network and Regression Analysis
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
by: Khan, Ahsan Ali, et al.
Published: (2011)

New approach in cost structuring of high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Flank wear modeling in high speed turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2009)

Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Tool wear and surface finish investigation in high speed turning using cermet insert by applying negative rake angles
by: Adesta, Erry Yulian Triblas, et al.
Published: (2009)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Prediction of crack growth propagation of a super alloy through ANN modeling
by: Muhammad Hasibul Hasan, Hasan, et al.
Published: (2015)

Wear characteristics of multiple particle size silicon carbide reinforced aluminium composite
by: Abdulmumin, Adebisi Adetayo, et al.
Published: (2015)

Modeling the effect of CNT concentration in dielectric fluid on EDM performance using neural network
by: Khan, Ahsan Ali, et al.
Published: (2016)

Energy cost modeling for high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Study on tool wear and tool life during milling JFRP using uncoated carbide cutting tool
by: Rashid, Mohammed Abdur N., et al.
Published: (2018)

Influence of single and multiple particle size variation on mechanical and wear behaviour of aluminium silicon carbide composites
by: Adebisi, Adetayo A., et al.
Published: (2015)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Dry machining of T6061 aluminium alloy using titanium nitride (TiN)and titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Cost analysis of using hybrid microwave post-sintered aluminium oxide inserts
by: Ariff, Tasnim Firdaus, et al.
Published: (2014)

Cutting temperature and surface roughness optimization in CNC end milling using multi objective genetic algorithm
by: Al Hazza, Muataz, et al.
Published: (2012)

Flank wear modeling in high speed hard end milling using integrated approach of Monte Carlo simulation method and Taguchi design
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2019)

Enhancing tool life of hot isostatically pressed silicon nitride inserts in machining inconel 718 with different susceptors through hybrid microwave post sintering
by: Ariff, Tasnim Firdaus, et al.
Published: (2018)

Dry machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Eco-friendly machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2012)

Investigation of the influence of chatter on tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Flank wears simulation by using back propagation neural network when cutting hardened H-13 steel in CNC End Milling
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Experimental study of flank wear in high speed turning of stainless steel AISI 304
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Tool life estimation model based on simulated flank wear during high speed hard turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2010)

Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
by: A.K.M., Nurul Amin, et al.
Published: (2007)

Investigation on the surface finish, MRR and the surface damage during the EDM of tungsten carbide
by: Khan, Ahsan Ali, et al.
Published: (2011)

TIG melted surface modified titanium alloy for automotive cylinder liner application
by: Adelek, S.A., et al.
Published: (2014)