Three-dimensional vibration analysis of fluid-filled
pipes

QR Code

Three-dimensional vibration analysis of fluid-filled pipes

A numerical model based on one-dimensional wave theory incorporating Poisson and junction coupling is used to carry out three-dimensional vibration analysis of a straight pipe filled with fluid. The Transfer Matrix Method is used to represent the fluid and structural vibration equations in the f...

Full description

Bibliographic Details
Main Authors:	Kolo, Isa, Idres, Moumen, Kafafy, Raed, Shaik Dawood, Mohd. Sultan Ibrahim
Format:	Proceeding Paper
Language:	English
Published:	2013
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/43908/ http://irep.iium.edu.my/43908/1/2013-Three-Dimensional_Vibration_Analysis_of_Fluid-Filled_Pipes.pdf

Similar Items

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Vibrational characteristics of piping system in air conditioning outdoor unit
by: Loh, S.K., et al.
Published: (2011)

Experimental study on energy absorption of foam filled kraft paper honeycomb subjected to quasi-static uniform compression loading
by: Aminanda, Yulfian, et al.
Published: (2016)

Hybrid non-destructive assessment for flow induced vibration piping systems using coupled fluid-structure interaction / Kong Keen Kuan
by: Kong , Keen Kuan
Published: (2020)

Transsient analysis of fluid structure interaction in straight pipe
by: Elghariani, Badreddin Giuma S. K.
Published: (2007)

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Modeling of compression systems
by: Idres, Moumen
Published: (2011)

Experimental and numerical study on the orthogonal and oblique impact on water filled pipes
by: Hussain Shah, Qasim
Published: (2011)

Two-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Experimental study of low-velocity impact on foam-filled kraft paper honeycomb structure
by: Abdul Kadir, Nurdina, et al.
Published: (2018)

Three-dimensional Analysis of Creep Voids
by: Wahab, A.A., et al.
Published: (2005)

Vibrational characteristics of piping system in air conditioning outdoor unit
by: Loh, S. K., et al.
Published: (2011)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

Modelling and structural analysis of three-dimensional wing
by: Mohd Zakuan, Muhammad Amir Mirza, et al.
Published: (2019)

Development of ceramic extruder for three dimensional printing
by: Lim, Chun Yong
Published: (2022)

Three-dimensional printing of lean clay ceramics
by: Tan, Seng Wah
Published: (2022)

Micromolding of three-dimensional components
by: Hung, W. N. P., et al.
Published: (2001)

Demonstration of Flow Separation in Pipe Elbow Using ANSYS CFD Flotran for Fluid Mechanics Course
by: Sulaiman, S. A., et al.
Published: (2002)

Design of screw extruder for three-dimensional ceramic printing
by: Wu, Peng
Published: (2021)