Design optimization of Micro Air Launch Vehicle using differential evolution

QR Code

Design optimization of Micro Air Launch Vehicle using differential evolution

In this paper, we have used the differential evolution to optimize the design of a Micro Air Launch Vehicle and its launch trajectory. Since trajectory design of a launch vehicle requires prior knowledge of the masses and propulsion performance parameters of the Micro Air Launch Vehicle, whereas t...

Full description

Bibliographic Details
Main Authors:	Aldheeb, Mohammed, Kafafy, Raed, Idres, Moumen, Omar, Hanafy, Abido, Mohammad
Format:	Article
Language:	English
Published:	Instituto de Aeronautica e Espaco-IAE - Brazil 2012
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/43835/ http://irep.iium.edu.my/43835/1/2012-Design_Optimization_of_Micro_Air_Launch_Vehicle_Using_Differential_Evolution_PublishedPaper.pdf

Similar Items

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Design of an autopilot for an autonomous unmanned aerial vehicle
by: Idres, Moumen, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Design optimization of a hybrid electric vehicle powertrain
by: Mangun, Firdause, et al.
Published: (2017)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Vehicle fuel consumption and emission modelling: an in-depth literature review
by: Faris, Waleed Fekry, et al.
Published: (2011)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Design And Development Of An Insect-Inspired Micro Air Vehicle
by: Cheaw, Boon Hong
Published: (2019)

Micro Air Vehicle: Technology Review and Design Study
by: Ammoo, Mohd. Shariff, et al.
Published: (2006)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Small launch platforms for micro-satellites
by: Cappelletti, Chantal, et al.
Published: (2018)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

Improving the efficiency of micronozzle by heated sidewalls
by: Hameed, Amar Hasan, et al.
Published: (2011)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Vehicle profile optimization using central composite design for pedestrian injury mitigation
by: Venkatason, Kausalyah, et al.
Published: (2015)

Optimization of driving mode switching strategy for a multimode plug-in hybrid electric vehicle
by: Idres, Moumen, et al.
Published: (2019)

Optimization of driving mode switching strategy for a multimode plug-in hybrid electric vehicle
by: Idres, Moumen, et al.
Published: (2019)

An analysis on the lift generation for Coandă micro air vehicles
by: Djojodihardjo, Harijono, et al.
Published: (2014)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Modeling and analysis of flutter-based thin-film cantilever microgenerator
by: Abdul Hakim, Javid, et al.
Published: (2015)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Development and optimization of a vehicle front-end geometry model for improved pedestrian safety
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2014)

Design and mechanical analysis of a 3D-printed biodegradable biomimetic micro air vehicle wing
by: Salami, E., et al.
Published: (2016)

UMPSA launches Sustainable Practice Carbon Free Electric Vehicles
by: Mimi Rabita, Abd Wahit
Published: (2023)

Theoretical foundation and numerical analysis on Coandă effect for micro-air vehicle
by: Ahmed, Riyadh Ibraheem
Published: (2016)

Differential evolution optimization for constrained routing in Wireless Mesh Networks
by: Sanni, Mistura Laide, et al.
Published: (2014)

Design, Fabrication of IIUM Unmanned Air Vehicle
by: Omar, Ashraf A., et al.
Published: (2006)

Performance comparison of differential evolution and particle swarm optimization in constrained optimization
by: Iwan, Mahmud, et al.
Published: (2012)

Development of an optimal dragonfly-like flapping wing structure for use in biomimetic micro air vehicles / Praveena Nair Sivasankaran
by: Praveena Nair, Sivasankaran
Published: (2016)