One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle

QR Code

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle

Two thermoelements are formed as walls of a micronozzle to perform heating-cooling on a gas flowing between them. The model of heat transfer by conduction opposites to Peltier effect is built, including Joule heating, Seebeck effect and heat dissipation to the flowing gas. A general energy equati...

Full description

Bibliographic Details
Main Authors:	Hameed, Ammar, Kafafy, Raed, Idres, Moumen
Format:	Article
Language:	English
Published:	Inderscience Publishers 2012
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/43834/ http://irep.iium.edu.my/43834/1/2012-One-dimensional_analysis_of_thermoelement_IJESMS040401_2012.pdf

Similar Items

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Thermoelectrically controlled micronozzle - A novel application for thermoelements
by: Hameed, Amar Hasan, et al.
Published: (2012)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Modeling of non-uniform thermoelement devices subject to lateral heat convection
by: Kafafy, Raed, et al.
Published: (2011)

Improving the efficiency of micronozzle by heated sidewalls
by: Hameed, Amar Hasan, et al.
Published: (2011)

Generalized one-dimentional flow inside thermo-electrically controlled micronozzle
by: Hameed, Amar Hasan, et al.
Published: (2011)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Design of an autopilot for an autonomous unmanned aerial vehicle
by: Idres, Moumen, et al.
Published: (2011)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Two-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Unstructured finite volume for two-dimensional navier stokes equations.
by: Idres, Moumen
Published: (2011)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Single-walled carbon nanotube modelling based on one-and two-dimensional Cosserat continua
by: Zhang, Yu
Published: (2011)

Experimental study of masonry wall exposed to blast loading
by: Ahmad, S, et al.
Published: (2013)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Investigations on physical characteristics of three-dimensional coil structure for MEMS magnetometer
by: Sulaiman, Nadzril, et al.
Published: (2013)

Thermoelectric properties of nanostructured tetrathiotetracene iodide crystals in a two-dimensional model
by: Sanduleac, Ionel, et al.
Published: (2014)

Low-cost and sustainable organic thermoelectrics based on low-dimensional molecular metals
by: Huewe, Florian, et al.
Published: (2017)

Investigation of heat transfer effect on polymerase chain reaction
by: Kafafy, Raed Ismail
Published: (2012)

Modeling and analysis of flutter-based thin-film cantilever microgenerator
by: Abdul Hakim, Javid, et al.
Published: (2015)

Vehicle fuel consumption and emission modelling: an in-depth literature review
by: Faris, Waleed Fekry, et al.
Published: (2011)

Lateral side impact crash simulation of restrained 3 year old child
by: Shasthri, Sevaguru, et al.
Published: (2014)

One dimensional nonlinear integral operator with Newton–Kantorovich method
by: Eshkuratov, Zainidin K., et al.
Published: (2016)

Progress in one-dimensional nanostructures
by: Samykano, M.
Published: (2021)

Study of a Thermoelectric Air Duct System Assisted by Photovoltaic Wall for Space Cooling In Tropical Climate
by: Kashif, Irshad, et al.
Published: (2017)