Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions

QR Code

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions

Orifice meter is a flow measuring device which is widely used in various industrial applications. Although the device gives accurate measurement during steady flow, measurement errors related to square root and sampling errors are unavoidable if pulsations exist. This research investigatesand imp...

Full description

Bibliographic Details
Main Authors:	Abdullah, mohammad, Idres, Moumen
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2015
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/43821/ http://irep.iium.edu.my/43821/1/2015_Evaluation_of_Orifice_Flow_Meter_Accuracy_under_Pulsation_Conditions_.pdf

Similar Items

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

The influence of orifice insertionin radial swirling flow for low emissions combustion
by: Ishak, Mohmad Shaiful Ashrul, et al.
Published: (2008)

The fractal flow conditioner for orifice plate flow meters
by: Manshoor, B., et al.
Published: (2011)

Pulsation-assisted fluidised bed drying of heat-sensitive and sticky materials: effect of basic parameter, and pulsation-specific parameter
by: Luqman, Abdul Halim, et al.
Published: (2022)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2013)

A Study on the Use of Orifice Plates as Steam Traps
by: Sulaiman, S. A., et al.
Published: (2010)

Development Of Sonic Air Flow Meter
by: Arumugam, Sagaathevan
Published: (2019)

The effect of swirl number on discharge coefficient for various orifice sizes in a burner system
by: Ashrul Ishak, Mohamad Shaiful, et al.
Published: (2004)

Experimental research on heat transfer characteristics of a battery liquid-cooling system with ⊥-shaped oscillating heat pipe under pulsating flow
by: Hong Kun, Lu, et al.
Published: (2024)

The Effect of Various Diameters Orifice Nozzle Coolant on Surface Roughness Performance in CNC Turning
by: Zainal Ariffin, Selamat, et al.
Published: (2014)

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Modeling of compression systems
by: Idres, Moumen
Published: (2011)

Heat Transfer Perfomance Of A Synthetic Jet Generated By Diffuser-Shaped Orifice
by: Ismail, Mohd Azmi
Published: (2019)

Numerical simulation and validation of high-speed turbulent and chemically-reacting flows
by: Kamel, Mohammed, et al.
Published: (2015)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

A CFD Study of Low Pressure Wet Gas Metering Using Slotted Orifice Meters
by: Perumal, Kumar, et al.
Published: (2011)

Constrained model predictive control for proton exchange membrane fuel cell
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Fuel cell starvation control using model Predictive technique with laguerre and exponential weight functions
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Wet Gas Measurement with Slotted Orifice Meter - Effect of Geometry of Slots and Pressure
by: Perumal, Kumar, et al.
Published: (2011)

Accuracy of Bhatnagaar-Gross-Krook scheme in solving laminar viscous flow problems
by: Omar, Ashraf Ali E., et al.
Published: (2009)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Surge and rotating stall
by: Idres, Moumen
Published: (2011)

Compressor models
by: Idres, Moumen
Published: (2011)

A CFD simulation study on the effect of velocity and pressure distributions in wet gas metering using slotted orifice flow
by: Muhammad Syazuwan, Nordin
Published: (2015)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Experimental evaluation of heat flow from rectangular fins array under forced convection
by: Shahrizal, Ibrahim
Published: (2012)

Numerical simulation of supersonic and turbulent combustion with trans-verse sonic fuel injection
by: Kamel, Mohammed, et al.
Published: (2015)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Towards a numerical simulation of supersonic mixing & combustion
by: Kamel, Mohammed, et al.
Published: (2013)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)