Biodegradability and mechanical behaviour of sugar palm starch based biopolymer

QR Code

Biodegradability and mechanical behaviour of sugar palm starch based biopolymer

A new Sugar Palm Starch (SPS) based biopolymer was successfully developed using glycerol as plasticizer. The effect of glycerol concentration (viz., 15, 20, 30 and 40 by weight percent) to the mechanical properties of plasticized SPS biopolymer was investigated. From this investigation, it was fo...

Full description

Bibliographic Details
Main Authors:	Sahari, Japar, Sapuan, Mohd Salit, Zainudin, Edi Syams, Maleque, Md. Abdul
Format:	Article
Language:	English English
Published:	Science Publications 2014
Subjects:	T173.2 Technological change TA164 Bioengineering TJ163.26 Energy conservation TS Manufactures
Online Access:	http://irep.iium.edu.my/42428/ http://irep.iium.edu.my/42428/1/P87_2014_Sahari.pdf http://irep.iium.edu.my/42428/4/42428_Biodegradability%20and%20mechanical%20behaviour_SCOPUS.pdf

Similar Items

Vegetable-based biodegradable lubricating oil additives
by: Maleque, Md. Abdul, et al.
Published: (2003)

Reverse engineering of automotive piston
by: Arifutzzaman, A., et al.
Published: (2012)

Design and fabrication of natural woven fabric reinforced epoxy composite for household telephone stand
by: Sapuan, S. M., et al.
Published: (2005)

Performance, emissions and wear characteristics of an indirect injection diesel engine using coconut oil blended fuel
by: Masjuki, H.H., et al.
Published: (2001)

Analysis of solar desalination system using heat pump
by: Amin, Zakaria Mohd., et al.
Published: (2015)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

Numerical investigation of flow boiling in double-layer microchannel heat sink
by: Ahmed, Shugata, et al.
Published: (2014)

Numerical analysis of heat transfer and nanofluid flow in a triangular duct with vortex generator: two-phase model
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

A triangular double layer microchannel heat sink: effect of parallel and counter flow
by: Manaf, Hazli, et al.
Published: (2014)

Waste heat recovery in heat pump systems: solution to reduce global warming
by: Baradey, Yehya, et al.
Published: (2015)

Active control of suddenly expanded flow
by: Khan, Sher Afghan, et al.
Published: (2000)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Seder, Islam M.F., et al.
Published: (2014)

Modelling and validation of proton exchange membrane fuel cell (PEMFC)
by: Mohiuddin, A. K. M., et al.
Published: (2018)

Performance analyses of horizontal axis wind turbines using QBlade
by: Zuhdi, Amirul Hakim, et al.
Published: (2017)

Investigation of aluminum heat sink design with thermoelectric generator
by: Mohiuddin, A. K. M., et al.
Published: (2017)

Validated analytical modeling of diesel engine regulated exhaust CO emission rate
by: Faris, Waleed Fekry, et al.
Published: (2016)

Comparative heat transfer analysis in different mini-channel heat sinks
by: Afzal, Asif, et al.
Published: (2017)

Energy harvesting from aerodynamic instabilities: Current prospect and future trends
by: Bashir, Musavir, et al.
Published: (2018)

Numerical investigation of semiempirical relations representing the local Nusselt number magnitude of a pin fin heat sink
by: Siddiqi, Mohammad Umar, et al.
Published: (2019)

On numerical investigation of semi-empirical relations representing local nusselt number at lower nozzle-target spacing’s
by: Siddique, Mohd Umair, et al.
Published: (2019)

Threaded spikes for bluff body base flow control
by: Khan, Sher Afghan, et al.
Published: (2019)

Hydrocarbons as alternative refrigerants in domestic refrigerators
by: S, Parashurama, et al.
Published: (2019)

Control of ideally expanded and under expanded nozzle flows with micro jets
by: G M, Fharukh Ahmed, et al.
Published: (2016)

Investigation on producing silica from rice husk biomass
by: Uddin, M.N., et al.
Published: (2018)

Thermo-mechanical analysis and estimation of turbine blade tip clearance of a small gas turbine engine under transient operating conditions
by: Kumar, Rahul, et al.
Published: (2020)

Magnetically plucked piezoelectric energy harvester via hybrid kinetic motion
by: Azam, Huda, et al.
Published: (2019)

A desalination system utilizing solar ambient and waste energy
by: Hawlader, M N A, et al.
Published: (2011)

Transport analysis of an Air Gap Membrane Distillation (AGMD) process
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (2011)

Optimization of cooling systems in data centre by computational fluid dynamics model and simulation
by: Romadhon, Rahmat, et al.
Published: (2009)

Reconstruction and electronic properties of interface between carbon nanotubes and ferromagnetic co electrodes
by: Cuong, Nguyen Tien, et al.
Published: (2012)

Optimization of a cooling system in data centers
by: Ali, Maisarah, et al.
Published: (2012)

An active cooling system for photovoltaic module
by: Teo, H. G., et al.
Published: (2012)

Combined water and power plant (CWPP) — a novel desalination technology
by: Mahbub, Fazle, et al.
Published: (2009)

PERFORMANCE OF A SOLAR INTEGRATED HEAT PUMP AIR-CONDITIONER, WATER HEATER AND DRYER
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (2008)

Performance evaluation of a mechanical vapor compression desalination system
by: Bahar, Rubina, et al.
Published: (2004)

Economic evaluation of a solar water heating system
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (1987)

Pretreatment of seawater: Results of pilot trials in Singapore
by: Chua, K T, et al.
Published: (2003)

Performance of thermoplastic sugar palm starch biopolymers
by: Sahari, J., et al.
Published: (2019)

EMK 402 - SISTEM PENUKARAN TENAGA OKT-NOV 1994.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (1994)

EMH 462(3) - ENERGY CONVERSION SYSTEM APRIL 07.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2007)