High quality acquisition of surface electromyography – conditioning circuit design

QR Code

High quality acquisition of surface electromyography – conditioning circuit design

The acquisition of Surface Electromyography (SEMG) signals is used for many applications including the diagnosis of neuromuscular diseases, and prosthesis control. The diagnostic quality of the SEMG signal is highly dependent on the conditioning circuit of the SEMG acquisition system. This pap...

Full description

Bibliographic Details
Main Authors:	Shobaki, Mohammed M., Abdul Malik, Noreha, Khan, Sheroz, Nordin, Anis Nurashikin, Haider, Samnan, Larbani, Sofiane, Arshad, Atika, Tasnim, Rumana
Format:	Article
Language:	English
Published:	IOP Publishing 2013
Subjects:	TK7800 Electronics. Computer engineering. Computer hardware. Photoelectronic devices
Online Access:	http://irep.iium.edu.my/41258/ http://irep.iium.edu.my/41258/1/1757-899X_53_1_012027.pdf

Similar Items

Inductive loops for sensing position as signature signals
by: Larbani, Sofiane, et al.
Published: (2013)

RLC circuit response
by: Tasnim, Rumana, et al.
Published: (2011)

Acquisition of a very low voltage and a low frequency biomedical signal- frequency selective filter design
by: Shobaki, Mohammed M., et al.
Published: (2014)

RC circuit response
by: Arshad, Atika, et al.
Published: (2011)

Posture characterization based on time and frequency domains parameters for erector spine SEMG signal
by: Shobaki, Mohammed M., et al.
Published: (2014)

Sensors in electronic applications
by: Tasnim, Rumana, et al.
Published: (2011)

Output control devices : actuators
by: Tasnim, Rumana, et al.
Published: (2011)

On the electrode arrangements of capacitive sensor for two phase Gas flow measurement
by: Tasnim, Rumana, et al.
Published: (2011)

Application and case studies of magnetic induction
by: Arshad, Atika, et al.
Published: (2011)

Magnetic hysteresis theory :application perspective
by: Arshad, Atika, et al.
Published: (2011)

The principle of resistive sensing
by: Arshad, Atika, et al.
Published: (2011)

Inductive power system for energy harvesting
by: Arshad, Atika, et al.
Published: (2011)

Capacitive sensing for non-contact means of measurement
by: Tasnim, Rumana, et al.
Published: (2011)

Contact type and noncontact type gas flow measuring sensors
by: Tasnim, Rumana, et al.
Published: (2011)

Basic concept of inductance for inductive transducers
by: Arshad, Atika, et al.
Published: (2011)

Magnetic properties for magnetic transducer
by: Arshad, Atika, et al.
Published: (2011)

Design and hardware implementation of conditioning circuit for accurate reading from transducers with nonlinear responses
by: Hasan, Khairul, et al.
Published: (2011)

Simple capacitive floor occupancy sensor for determining the pattern of a walking person
by: Arshad, Atika, et al.
Published: (2018)

Equivalent circuit modeling of two-port Al-doped Zinc Oxide CMOS SAW resonator using MATLAB™
by: Md Ralib @ Md Raghib, Aliza 'Aini, et al.
Published: (2013)

Dependence of preferred c-axis orientation on RF magnetron sputtering power for AZO/Si acoustic wave devices
by: Md Ralib @ Md Raghib, Aliza 'Aini, et al.
Published: (2015)

Functional electrical stimulation system and profile for walking
by: Abdul Malik, Noreha
Published: (2011)

Optimized RC timing technique for accurate measurement of minute capacitance changes
by: Zaharudin, Zarimin, et al.
Published: (2018)

Optical-resonator-based biosensing systems: current status and future prospects
by: Nordin, Anis Nurashikin
Published: (2016)

Design and simulation of 10 MHz MEMS oscillator
by: Taufik, Mohamad Syamsi, et al.
Published: (2014)

Design and simulation of 20MHz oscillator using CMOS-MEMS beam resonators
by: Zainuddin, Ahmad Anwar, et al.
Published: (2013)

Modeling and development of radio frequency planar interdigital electrode sensors
by: Yunos, Muhammad Farhan Affendi, et al.
Published: (2019)

Sensor and sensor response-issues and interfacing
by: Ahmmad, Syed Masrur, et al.
Published: (2011)

Design of two-stage CMOS amplifier for quartz crystal resonator
by: Mohd Taufik, Muhammad Syamsi, et al.
Published: (2013)

A study on controllable aluminium doped zinc oxide patterning by chemical etching for MEMS application
by: Md Ralib @ Md Raghib, Aliza 'Aini, et al.
Published: (2017)

Design and simulation of Clamped-Clamped and Clamped-Free resonators
by: Zainuddin, Ahmad Anwar, et al.
Published: (2013)

Intelligent flood disaster warning on the fly: developing IoT-based management platform and using 2-class neural network to predict flood status
by: Abdullahi, Salami Ifedapo, et al.
Published: (2019)

Capacitive electrode sensor: design and testing
by: Abdullahi, Salami Ifedapo, et al.
Published: (2018)

Flood disaster warning system on the go
by: Abdullahi, Salami Ifedabo, et al.
Published: (2018)

Intelligent flood disaster warning on the fly: developing IoT-based management platform and using 2-class neural network to predict flood status
by: Abdullahi, Salami Ifedapo, et al.
Published: (2019)

Design, simulation and practical experimentation of miniaturized turbine flow sensor for flow meter assessment
by: Ifedapo Abdullahi, Salami, et al.
Published: (2019)

Implementation of CMOS oscillator for CMOS SAW resonator
by: Karim, Jamilah, et al.
Published: (2016)

An estimation of the coupling coefficient of the series inductive resonant wireless power transfer coils
by: Adam, Ismail, et al.
Published: (2020)

RF CMOS-MEMS cantilever resonator
by: Zainuddin, Ahmad Anwar, et al.
Published: (2013)

Theoretical modelling of interdigitated electrode sensor for mammalian cell characterization
by: Mohd Mansor, Ahmad Fairuzabadi, et al.
Published: (2018)

The load reliant power transfer of the series-to-series inductive resonant wireless power transfer
by: Adam, Ismail, et al.
Published: (2020)