Numerical investigation of flow boiling in double-layer microchannel heat sink

QR Code

Numerical investigation of flow boiling in double-layer microchannel heat sink

Double-layer microchannel heat sinks (DL-MCHS) are considered as an effective solution of temperature non-uniformity on the surface of microelectronic devices. However, only single-phase flow is analyzed so far in DL-MCHS. In this paper, numerical investigation has been carried out to observe the...

Full description

Bibliographic Details
Main Authors:	Ahmed, Shugata, Seder, Islam M.F., Ab. Manaf, Hazli, Ahmed, Mirghani Ishak, Hawlader, Mohammad Nurul Alam
Format:	Article
Language:	English
Published:	INSI Publications 2014
Subjects:	TJ170 Mechanics applied to machinery. Dynamics
Online Access:	http://irep.iium.edu.my/39310/ http://irep.iium.edu.my/39310/1/Numerical_Investigation_of_Flow_Boiling_paper.pdf

Similar Items

Numerical investigation of flow boiling in double-layer microchannel heat sink
by: Ahmed, Shugata, et al.
Published: (2014)

A triangular double layer microchannel heat sink: effect of parallel and counter flow
by: Manaf, Hazli, et al.
Published: (2014)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Seder, Islam M.F., et al.
Published: (2014)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

Experimental and numerical study on the orthogonal and oblique impact on water filled pipes
by: Hussain Shah, Qasim
Published: (2011)

EMH 451-3 - NUMERICAL METHODS FOR ENGINEERS NOV 10.
by: ppkm, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2010)

Numerical investigation of heat transfer of a multi-layered microchannel heat sink with tapered channel
by: Zuo, Jiawei
Published: (2023)

Modelling and simulation of double-link scenario in a two-wheeled wheelchair
by: Ahmad, Salmiah, et al.
Published: (2014)

Development of design structure matrix of product architecture case study: multi purpose CNC router
by: Hilmy, Irfan, et al.
Published: (2014)

Implementation of lean manufacturing to blend with good manufacturing practice at Minda Tulus Industries Sdn. Bhd. for improved performance
by: Nasry, Nasrul Ashraf, et al.
Published: (2017)

Performance and cost analysis of diesel engine with different mixing ratio of raw vegetable oil and diesel fuel
by: Uddin, Md. Nasir, et al.
Published: (2016)

Modal analysis of car panels using finite element analysis
by: Hanouf, Zahir
Published: (2011)

Biodiesel production process optimization from spirulina maxima microalgae and performance investigation in a diesel engine
by: Rahman, Md Atiqur, et al.
Published: (2017)

Image-based feature extraction technique for inclined crack quantification using pulsed eddy current
by: Nafiah, Faris, et al.
Published: (2019)

Development of vibration suppression devices from smart fluids
by: Rashid, Muhammad Mahbubur, et al.
Published: (2011)

Development of fuzzy logic controller for magnetorheological rotary brake system
by: Rashid, Muhammad Mahbubur, et al.
Published: (2009)

Dynamics and control policies analysis of semi-active suspension systems using a full-car model
by: Ihsan, Sany Izan, et al.
Published: (2007)

An evaluation of LQR and fuzzy logic controllers for active suspension using half car model
by: Hasbullah, Faried, et al.
Published: (2010)

A study of noise transmission through cylindrical shell using modal truncation approach
by: El-Hafidi, Ali, et al.
Published: (2011)

Dynamic characterisation of elastomeric engine mounts of different geometry used in automotive industry: simulation approach
by: Faris, Waleed Fekry, et al.
Published: (2010)

Active engine mounting controller using extended minimal resource allocating networks
by: Darsivan, Fadly Jashi, et al.
Published: (2008)

Investigation into noise problems in vehicle structure using vibro-acoustic approach
by: Hanouf, Zahir Ahmad, et al.
Published: (2009)

Evaluation of friction welded bi-material joint strength subjected to impact loads
by: Shah, Qasim Hussain, et al.
Published: (2011)

Aerodynamic derivatives identification for ground vehicles in crosswind using neural network and PCA
by: Ramli, Nabilah, et al.
Published: (2010)

Load carrying capability of liquid filled cylindrical shell structures under axial compression
by: Hussain Shah, Qasim, et al.
Published: (2011)

Finite element modelling of damage fracture and fretting fatigue
by: Wahab, M. Abdel, et al.
Published: (2012)

Effect of tapered angle of a conical nose indenter on the energy absorbing variation of a copper pipe subjected to axial crushing
by: Shah, Qasim Hussain, et al.
Published: (2012)

A comparison of energy absorbing capabilities of paper and steel structures subjected to progressive failure under free falling objects
by: Shah, Qasim Hussain, et al.
Published: (2007)

The damage of unconfined granite edge due to the impact of varying stiffness projectiles
by: Shah, Qasim Hussain, et al.
Published: (2013)

LS-DYNA for beginners: an insight into Ls-Prepost and Ls-Dyna
by: Hussain Shah, Qasim, et al.
Published: (2012)

Monitoring of fatigue damage using ultrasonics and finite element analysis
by: Hrairi, Meftah, et al.
Published: (2012)

Analysis of thermal stress intensity factors for edge cracked bimaterial system
by: Hrairi, Meftah, et al.
Published: (2012)

Development of palmprint based biometric system
by: Rotinwa-Akinbile, M. A., et al.
Published: (2011)

Kernel PCA – an introduction
by: Baali, Hamza, et al.
Published: (2011)

System modelling of a twin rotor system: time and frequency domain analysis
by: Toha, Siti Fauziah, et al.
Published: (2011)

Review of Malaysian traffic summon and payment system
by: Aibinu, Abiodun Musa, et al.
Published: (2011)

Hot Water Rocket System (HWRS) - preliminary design and prototype development of a pressurized how water casing (PHWC)
by: Kashif, Syed Muhammad
Published: (2012)

EMK 311 - MEKANIK BENDALIR II OKT-NOV 1994.
by: PPKEE, Pusat Pengajian Kejuruteraan Elektrik & Elektronik
Published: (1994)

EMM 322E(3) - HINGAR & GETARAN MEI 05.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2005)

EMM 322E(3) - NOISE AND VIBRATION APRIL 07
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2007)